Abstract:With the increasing demand for multidirectional vibration measurements, traditional triaxial accelerometers cannot achieve vibration measurements with high sensitivity, high natural frequency, and low cross-sensitivity simultaneously. Moreover, for piezoresistive accelerometers, achieving pure axial deformation of the piezoresistive beam can greatly improve performance, but it requires the piezoresistive beam to be located in a specific position, which inevitably makes the design more complex and limits the performance improvement. Here, a monolithically integrated triaxial high-performance accelerometer with pure axial stress piezoresistive beams was designed, fabricated, and tested. By controlling synchronous displacements at both piezoresistive beam ends, the pure axial stress states of the piezoresistive beams could be easily achieved with position independence without tedious calculations. The measurement unit for the z-axis acceleration was innovatively designed as an interlocking proof mass structure to ensure a full Wheatstone bridge for sensitivity improvement. The pure axial stress state of the piezoresistive beams and low cross-sensitivity of all three units were verified by the finite element method (FEM). The triaxial accelerometer was fabricated and tested. Results showing extremely high sensitivities (x axis: 2.43 mV/g/5 V; y axis: 2.44 mv/g/5 V; z axis: 2.41 mV/g/5 V (without amplification by signal conditioning circuit)) and high natural frequencies (x/y axes: 11.4 kHz; z-axis: 13.2 kHz) were obtained. The approach of this paper makes it simple to design and obtain high-performance piezoresistive accelerometers.

Micromachined Piezoresistive Accelerometers Based on an Asymmetrically Gapped Cantilever

Mechanical Design Optimization of A Single-Axis Moems Accelerometer Based on A Grating Interferometry Cavity for Ultrahigh Sensitivity

Piezoresistive Slot-Cantilever Type Accelerometer Inspired from Spider'S Slit Sensilla

A High-Performance Micromachined Piezoresistive Accelerometer with Axially Stressed Tiny Beams

Dynamic Analysis of Piezo-Based Accelerometer with Asymmetric Gapped Cantilever Array

Development of A Novel Two Axis Piezoresistive Micro Accelerometer Based on Silicon

Design, Fabrication, and Characterization of a High-Performance Monolithic Triaxial Piezoresistive High-g Accelerometer

A Piezoresistive Accelerometer with Axially Stressed Tiny Beams for Both Much Increased Sensitivity and Much Broadened Frequency Bandwidth

A Micromachined Piezoresistive High-G Accelerometer With High Sensitivity And Wide Frequency-Band: Design And Modeling

A Miniaturized Piezoelectric MEMS Accelerometer with Polygon Topological Cantilever Structure.

Monolithically Integrated Triaxial High-Performance Micro Accelerometers with Position-Independent Pure Axial Stressed Piezoresistive Beams

Ultra-high-sensitivity micro-accelerometer achieved by pure axial deformation of piezoresistive beams

High-Performance Single-Side Fabricated (111)-Silicon Dual-Cantilever Accelerometer with Squeeze-Film Air Damping Modulation

Analysis and Design of a Novel Piezoresistive Accelerometer with Axially Stressed Self-Supporting Sensing Beams

Fabrication and Testing of a Silicon-Based Piezoresistive Two-Axis Accelerometer

A Micromachined Silicon-on-Glass Accelerometer with an Optimized Comb Finger Gap Arrangement

Development of a MEMS Piezoresistive High-g Accelerometer with a Cross-Center Block Structure and Reliable Electrode

Design and Simulation of A Novel Highly Symmetrical Piezoelectric Triaxial Accelerometer

Design of a Triaxial Piezoelectric Accelerometer

Analysis of Thin Film Piezoelectric Microaccelerometer Using Analytical and Finite Element Modeling

Development of a High-Performance Microaccelerometer With Position Independent Pure-Axial Stressed Piezoresistive Beams