Abstract:Supercritical CO2 cycles offer a new thermal power generation paradigm but their commercial deployment has been slow due to significant turbine design challenges. Rotor bearings and seal design are identified as the critical challenges due to the high temperatures, high pressures, and high rotational speeds, a combination of extreme values not encountered in any other past turbine applications. This paper presents a new supercritical CO2 turbine configuration that addresses these challenges by introducing a rotor shaft cooling zone to control the temperatures encountered by the seals and the bearings. This makes it possible to use proven conventional seal and bearing technology. The salient feature is referred to as a 'cooling pillow' that cools the rotor shaft to a tolerable seal temperature by circulating supercritical CO2 fluid through the annulus and at the same time provides dynamic support to the rotating shaft against vibration. Turbulent heat transfer and frictional heat generation correlations for the annuli have been employed to evaluate the cooling performance and the simplified Reynolds equation for hydrodynamic fluid film lubrication has been employed to evaluate the dynamic performance. Design charts and figures are presented using non-dimensional parameters to help with the design of supercritical CO2 turbines at different temperatures and sizes. The COMSOL rotor-bearing system simulator consisting of bearing and disks with the main shaft has been employed to produce Campbell plots and carry out a parametric study of rotor vibration frequencies varying with the cooling zone design. The cooling capacity is found to be significantly higher than the cooling load required. Moreover, the convection heat transfer coefficient and dimensionless temperature distribution are independent of radial clearance and this offers trade-offs in terms of controlling rotor vibrations. Through the pursuit of such trade-offs, it is demonstrated that dynamic performance can be improved by up to 55% and 60% for the 0.5 MW and 10 MW turbine sizes, respectively.

Conceptual Design of the Cryogenic System for A 12 Mw Superconducting Wind Turbine Generator

Design and Analysis of a Superconducting Induction Magnetic Levitation Device for Hydraulic Turbo-Generator

Design and Comparison of Segmented Armature Windings for Superconducting Wind Turbine Generators with Multiple Converters

Design of A 10 Mw Dual-Stator Superconducting Permanent Magnet Wind Power Generator

Design Study of a 10-Kw Fully Superconducting Synchronous Generator

Design and Test of a Simplified and Reliable Cryogenic System for High Speed Superconducting Generator Applications

Design and Test of a Novel Thermal Insulated Torque Coupling for a 15-Kw Fully HTS Synchronous Generator

Design Aspects for Permanent Magnet Superconducting Wind Power Generators

Stepped-shape Field Winding Optimization of a Large Capacity HTS Aircraft Propulsion Machine

General Design of a 300-Kvar HTS Synchronous Condenser Prototype

Design a cooling pillow to support a high-speed supercritical CO2 turbine shaft

AC Loss Analysis and Modular Cryostat Design of a 10-MW High-Temperature Superconducting Double Stator Flux Modulation Machine

Design of the Onboard Cryogenic System for High-Temperature Superconducting Maglev Vehicle

A Pole Pair Segment of Oil-cooling Air-Core Stator for a 2 MW Direct-Drive High Temperature Superconducting Wind Power Generator

Thermal Analysis for the Hts Stator Consisting of Hts Armature Windings and an Iron Core for A 2.5 Kw Hts Generator

Remote cryogenic helium gas circulating cooling system for a 10-Mvar class HTS dynamic synchronous condenser

Liquid Hydrogen Cooling System for 100 kW-Class HTS Rotor thermal Design

Design Of A Dual-Stator Superconducting Permanent Magnet Wind Power Generator With Different Rotor Configuration

A Long-Life, High-Capacity and High-Efficiency Cryogenic System Developed for High-Tc Superconducting Magnet Applications

Design and Experimental Investigations on the Helium Circulating Cooling System Operating at Around 20 K for a 300-kvar Class HTS Dynamic Synchronous Condenser