Abstract:Continuous improvement of high temperature superconducting (HTS) materials has lead to a thriving development of various applications including superconducting motor, superconducting power transmission cable and superconducting power generator. Those applications, in common, require a high-capacity and highly reliable cooling solution to keep the superconducting material at the proper temperature. To meet such a requirement, a high capacity GM cryocooler which can provide about 650 W cooling power at 80 K1 was developed. Since the physical size of this prototype unit is considerably larger compared with current available GM cryocoolers, parameters including regenerator size and valve timing should be redesigned carefully in order to get an optimized performance. type unit became available, the design was improved by feeding back the experiment results to the prototype units. In this paper, both the simulation method and experimental results will be reported. INTRODUCTION Since its invention in 1950s2, Gifford-McMahon (GM) cryocooler is known as one of the most reliable commercial cryocooler for multiple applications including cryopumps, cooling of the radiation shield for an MRI, and cooling of infrared sensors for the military3. Most of the development of the GM cryocooler in last decade focused on increasing cooling performance near 4 K, performance optimization in the 4-30K temperature region and increasing the Carnot efficiency. Development of high heat capacity materials played an important role in this stage. In the 1990s, the development of rare earth materials made it possible for a GM cryocoolers to reach a temperatures near 4K. Recently, by utilizing a new rare earth material, Gd2O2S (GOS) 4, a prototype compact GM cryocooler which can reach 2.1K under no-load conditions was developed5-6. On the other hand, rapid growth of high temperature superconducting (HTS) material applications brings new challenges to the current cryocoolers. In contrast to the 4K region applications, HTS applications often require much more cooling power with relatively high cooling temperature of 80K is acceptable. Applications including HTS superconducting motors, power transmission lines and power generators are usually considered to consume 102 W to 104 W cooling power (per 291 Cryocoolers 19, edited by S.D. Miller and R.G. Ross, Jr. ©¶International Cryocooler Conference, Inc., Boulder, CO, 2016 C19_013 2 case). Most of these applications are currently using direct liquid nitrogen cooling or Turbo-Brayton current commercial GM cryocoolers lack the suitable cooling power which is crucial in HTS applications. In the current market, even the largest GM cryocooler (scotch-yoke driven) can only provide about 100 W at 30K (with a 7 kW compressor unit)7. oped. After the design optimization of valve size, valve timing and regenerator material arrangement, a typical cooling capacity of about 650 W at 80K was achieved with an input power of about 13 kW. In this paper, the latest experiment results and optimization method will be described. GENERAL DESIGN ASPECTS A typical single stage, scotch-yoke driven GM type cryocooler design was chosen to be the start point of our development. As shown in Figure 1, the pressure wave is generated by a typical rotary valve. Pressure gauges which were used to monitor the compression and expansion room pressure are only utilized in the experiment. A 200 W brushless electric motor with controllable rotation speed is used to drive the motion of scotch-yoke. Figure 2 shows the more realistic external view of the current prototype unit. The physical size of this unit is about 680 mm in height and 640 mm in width. The rotary valve is designed to be changeable so the operation timing and opening area can be easily optimized. Also the displacer is designed to be reopened for the arrangement of metal mesh inside to be changed. In order to roughly determine the physical size of the expansion room, displacer and to achieve performance prediction. SIMULATION METHOD AND RESULTS Simulation Method Description timate the main loss in the prototype cryocooler. The compressibility of helium is taken into count by the continuity equation: (1) U is the velocity vector. mesh in the displacer. Figure 1. A simplified diagram of the prototype cryocooler. GM & GM-TYPE PULSE TUBE COOLER DEVELOPMENTS 292

Design and Test of a Simplified and Reliable Cryogenic System for High Speed Superconducting Generator Applications

Development of A High Speed Hts Generator for Airborne Applications

35 Kj/7 Kw Conduction-cooled High Tc Superconducting Magnet Energy Storage

Development of a Conduction-Cooled HTS SMES

Numerical Study on the Working Performance of a G-M Cryocooler with a Mechanically Driven Displacer

Analysis of 1.8 K Superfluid Helium Cryogenic System for Cooling Superconducting Magnets

A Long-Life, High-Capacity and High-Efficiency Cryogenic System Developed for High-Tc Superconducting Magnet Applications

Over-Current Simulation Test for High Temperature Superconducting Generator

Design of A Cryogenic System for A 20m Direct Current Superconducting Mgb2 and Ybco Power Cable

Variable Temperature Thermal Conductivity and Conductance Measurements Using a Gifford-McMahon Cryocooler

First tests of a 800 kJ HTS SMES

Development Status of a High Cooling Capacity Single Stage GM Cryocooler

Superconducting Feeder System For Iter Central Solenoid Module Final Test Facility

RETRACTED: Development of a Cryogenic Test Bed for High Amperage Critical Current Measurement on High Temperature Superconductor Wire

Development and Performance Test of 40W/30 K Single Stage G-M Cryocooler with Large Refrigerating Capacity

Design Study for a Superconducting High-Power Fan Drive for a Long-Range Aircraft

Design of the Onboard Cryogenic System for High-Temperature Superconducting Maglev Vehicle

Magnetic Conduction Structure Design and Charging Test of a Linear-Motor Type Flux Pump for Through-Dewar Excitation of High Temperature Superconducting Motors

Development and Testing of a 300-Kvar HTS Synchronous Condenser Prototype

Design Study of a 10-Kw Fully Superconducting Synchronous Generator

Conceptual design, AC loss calculation, and optimization of an airborne fully high temperature superconducting generator