Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Numerical Simulation of Silicon Micro Flat Heat Pipes with Axial Triangle Grooves

Design, Simulation and Fabrication of A Silicon Micro Flat Heat Pipe with Axial Triangle Grooves

Thermal Analysis and Maximum Heat Transport of a Micro Flat Heat Pipe with Axial Triangle Grooves

Theoretical Analysis and Experimental Investigation on Designing Method of Micro-Groove Heat Pipe

Three-dimensional analysis of heat transfer in a micro-heat sink with single phase flow

Simulation of gas flow and heat transfer in micro Poiseuille flow

Simulation of Flow and Heat Transfer in Micro Couette Flow

Mathematical Model and Numerical Simulation of Flow and Heat Transfer in LHP's Capillary Wick with Azimuthal Vapor Grooves

Characteristics of a Micro Flat Heat Pipe with Trapezoidal Grooves

Investigation on Microheat Pipe Array with Arteries

Numerical simulation on heat and mass transfer in gravity heat pipe

The Numerical Modeling of the Vapor Bubble Growth on the Silicon Substrate Inside the Flat Plate Heat Pipe

A numerical study of laminar convective heat transfer in microchannel with non-circular cross-section☆

On Numerical Simulation Techniques of Stable Crack Growth

Numerical Investigation of High-Temperature Heat Pipes with Different Wick Structures under Non-Uniform Heating Boundary Conditions

Numerical Simulation of Micro Scale Flowing and Boiling

Numerical Analysis of Flow Boiling Characteristics of a Single Channel Heat Sink Subjected to Multiple Heat Sources

Numerical Simulations of the Liquid-Vapor Phase Change Dynamic Processes in a Flat Micro Heat Pipe

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink

A Mathematical Model for Optimizing the Structure of A Flat Micro Heat Pipe with Fiber Wick

Numerical simulation of fluid and heat transfer characteristics of microchannel heat sink with fan-shaped grooves and triangular truncated ribs