Abstract:Temperature is a key factor that affects the performance of power batteries, because excessive operating temperatures and uneven temperature distribution may accelerate the degradation rate of batteries and shorten their lifespans. Therefore, an efficient battery thermal management system is required to keep the battery temperature within the desirable operating range. Traditional cooling methods, including air cooling and liquid cooling, are limited in efficient heat extraction for a large amount of heat generation from fast charging batteries. Heat pipe technologies, especially micro heat pipe arrays, have attracted lots of attention due to the superior thermal conductivity. However, micro heat pipe arrays in battery thermal management need to be further studied under high heat power density conditions and need to be further developed in the structural optimization design.In this paper, a micro heat pipe array is adopted as a heat conduction element for a battery thermal management system. Then, the temperature performance of the micro heat pipe array is analyzed and the equivalent thermal conductivity is calculated theoretically. To further enhance the heat transfer capability of the micro heat pipe array, the internal fluid flow and heat transfer characteristics are investigated by adjusting groove parameters. In addition, the thermal performance of micro heat pipe array is compared with that of a traditional sintered heat pipe group and latest published results. The experimental and theoretical studies show that when the heat power density is below 0.3658 W cm−2, the surface temperature at the evaporator section of micro heat pipe array can be maintained at below 45°C and the temperature difference can be controlled at below 1.3°C. As the heat power density increases to 0.9176 W cm−2, the equivalent thermal conductivity of the micro heat pipe array increases to 6027 W m−1 K−1, and the maximum temperature difference of the evaporator section is well controlled at 2.75°C. Furthermore, increasing the height and width of the grooves in the micro channel has a positive effect on the equivalent thermal conductivity. The results show that the figure will increase by 129% when the height of the groove increases from 0.01 to 0.47 mm. However, changing the width of the groove can weaken the capillary force which drives liquid return inside the channel. In order to prove the potential capability in broad electric vehicles application, related experiments have been carried out under dynamic power conditions and at low temperature environments. The results revealed that the micro heat pipe array has a fast thermal response and stable performance to dynamic heat powers. At −4°C environments, the temperature of the micro heat pipe array could reach 20°C in 2 min if given a heat power of 0.36 W cm−2. Compared with the thermal performance of a traditional sintered heat pipe group, the micro heat pipe array can reduce the maximum temperature by 15.1°C and the temperature difference by 14°C. Overall, the micro heat pipe array shows excellent capability in controlling the temperature rise and minimizing the temperature difference, and the advantages become more obvious at high heat power densities. This shows that micro heat pipe arrays have broad application prospects in the future. All the results from the study could further support the development of battery thermal management systems and the heat transfer enhancement of micro heat pipe arrays.

Investigation on Microheat Pipe Array with Arteries

Analysis on Heat Resistance of the Micro Heat Pipe with Arteries

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

Heat Transfer Capacity Optimization Design of Microgroove and Microcolumn in an Ultra-Thin Flat Heat Pipe

Thermal Characterisation of Micro Flat Aluminium Heat Pipe Arrays by Varying Working Fluid and Inclination Angle

Experimental investigation and analytical prediction of a multi-channel flat heat pipe thermal performance

Investigation of Thermal Characteristics and Two-Phase Flows of a Star-Shape Thin Heat Pipe

Heat transfer performance of a micro heat pipe array for battery thermal management systems

Experimental and theoretical investigation of the influence of heat transfer rate on the thermal performance of a multi-channel flat heat pipe

Experimental and simulation study on flow heat transfer characteristics of flat pulsating heat pipe with wide and narrow interphase channels

Numerical Investigations of the Thermal-Hydraulic Characteristics of Microchannel Heat Sinks Inspired by Leaf Veins

Experiments and comparisons of three miniature heat pipes' thermal performance

CFD simulation based on film model of high temperature potassium heat pipe at different positions: Horizontal, vertical, and 45° inclined

Evaluation of the thermal and hydraulic performances of a very thin sintered copper flat heat pipe for 3D microsystem packages

Three-Dimensional Numerical Analysis of Mini-Grooved Flat Heat Pipe Filled with Different Working Fluids with Experimental Validation

An Experimental Investigation on the Heat Transfer Characteristics of Pulsating Heat Pipe with Adaptive Structured Channels

STUDY ON TWO-PHASE FLOW AND TEMPERATURE UNIFORMITY CHARACTERISTICS OF MICROCHANNEL HEAT PIPE

Design and Experimental Analysis of Grooved Flat Aluminum Heat Pipe

Experimental Study on Enhanced Heat Transfer Capability of the Array of Microtubes

A study of liquid flow in a flat plate heat pipe under localized heating