Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Intrinsic Fabry-Perot interferometer with a micrometric tip for biomedical applications

Sensitivity-enhanced Optical Sensor Based on Multilayer Coated Fabry–Pérot Interferometer

Micro Multicavity Fabry–Pérot Interferometers Sensor in SMFs Machined by Femtosecond Laser

Femtosecond Laser Fabricated In-Line Micro Multicavity Fiber FP Interferometers Sensor

Ultracompact Fiber Sensor Tip Based on Liquid Polymer-Filled Fabry-Perot Cavity with High Temperature Sensitivity

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Polymer Microbubble-Based Fabry–Perot Fiber Interferometer and Sensing Applications

Micromachining of an In-Fiber Extrinsic Fabry-Perot Interferometric Sensor by Using a Femtosecond Laser

Ultracompact Optical Fiber Sensor for Inner Diameter Measurement

Optical Fiber Fabry–Pérot Microfluidic Sensor Based on Capillary Fiber and Side Illumination Method

A novel micromachined Fabry-Perot interferometer integrating nano-holes and dielectrophoresis for enhanced biochemical sensing

High-Q Fabry-Pérot Cavity Based on Micro-Lens Array for Refractive Index Sensing

Micromachining of an In-Fiber Extrinsic Fabry-Perot Interferometric (MEFPI) Sensor by Using a Femtosecond Laser

Asymmetric Fabry-Pérot interferometric cavity for fiber optical sensors

Two-photon 3D Printed Fiber-Optic Fabry-Perot Probe for Triaxial Contact Force Detection of Guidewire Tips

An Open-Cavity Fiber Fabry-Perot Interferometer Fabricated by Femtosecond Laser Micromachining for Refractive Index Sensing

3D printed fiber-optic nanomechanical bioprobe

Microfiber-Enabled In-line Fabry–Pérot Interferometer for High-Sensitive Force and Refractive Index Sensing

Highly Precise In-Plane Displacement Sensor Based on an Asymmetric Fiber Fabry-Perot Interferometer.

Miniature All-Fiber Fabry-Perot Interferometer

High-Temperature Sensor Based on Fabry-Perot Interferometer in Microfiber Tip