Photonic Bandgap Tuning With Thermo-Optic Effect

T Chu,H Yamada,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/LEOS.2004.1363488

2004-01-01

Abstract:Tuning of photonic bandgap was demonstrated with thermo-optic effect. A 2.7-nm wavelength-shift was obtained at 48 mW heating power. Optic switching by shifting photonic bandgap was realized with an extinction ratio of 13 dB.

What problem does this paper attempt to address?

Temperature-controlled transformation in fiber types of fluid-filled photonic crystal fibers and applications.

Yiping Wang,Xiaoling Tan,Wei Jin,Diqing Ying,Yeuk Lai Hoo,Shujing Liu

DOI: https://doi.org/10.1364/OL.35.000088

IF: 3.6

2010-01-01

Optics Letters

Abstract:We investigated experimentally and theoretically an invertible fiber-type transformation from a photonic bandgap fiber into a nonideal waveguide and then into an index-guiding photonic crystal fiber via the thermo-optic effect of the fluid filled in the air holes. Such a transformation could be used to develop an in-fiber optical switch/attenuator with a high-extinction ratio of more than 35 dB over an extremely broad wavelength range from 600 to 1700 nm via a small temperature adjustment. (C) 2009 Optical Society of America
Tunable Optical Notch Filter Realized by Shifting the Photonic Bandgap in a Silicon Photonic Crystal Line-Defect Waveguide

Tao Chu,Hirohito Yamada,Akiko Gomyo,Jun Ushida,Satomi Ishida,Yasuhiko Arakawa

DOI: https://doi.org/10.1109/lpt.2006.887366

IF: 2.6

2006-01-01

IEEE Photonics Technology Letters

Abstract:A tunable optical notch filter was realized by thermally shifting the TM-like (the light's electric field perpendicular to the substrate) bandgap of a silicon photonic crystal slab W1 line-defect waveguide with silica cladding. This device is compact-its footprint is 340 x 16 mu m(2), excluding the electrode pads. The 3-dB bandwidth of the device was about 5 run, and the extinction ratio at the center wavelength was as high as 40 dB. A maximum center wavelength shift of 17.9 run was attained at a heating power of 0.7 W, with a tuning efficiency of 25.5 mn/W. The tuning response time was less than 100 mu s.
Controlling the photonic bandgap structures via manipulation of refractive index of electromagnetically induced transparency vapor

Fei Zhuang,Shen Jian-Qi,Jun Ye

DOI: https://doi.org/10.7498/aps.56.541

2007-01-01

Abstract:A new application of coherent manipulation of EIT (electromagnetically induced transparency) medium is suggested. A two-dimensional photonic crystal with a triangle lattice of elliptic air cylinders, which are filled with the EIT atomic vapor, in the KAs background material is designed. By manipulating the refractive index of the EIT vapor via the external control field, one can obtain the controllable bandgap structure that is sensitive to the variations of external conditions (e.g. the intensity of the control field) . It is shown that a large complete bandgap of about 0.0503ω e in the region of high normalized frequency could be achieved by choosing the specific parameters such as the spontaneous decay rate, dephasing rate, Rabi frequency of control light, atomic number density as well as elliptic geometric parameters.
Tunable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguides

H Yamada,T Chu,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/lpt.2006.877233

IF: 4

2005-01-01

Applied Physics Letters

Abstract:A wavelength tunable optical add-drop multiplexer based on silicon photonic wire waveguides with Bragg-grating-reflectors was demonstrated by tuning the dropping wavelength through thermooptic effect. A 6.6-nm dropping wavelength shift was obtained at a 0.82-W heating power. For the device that is presently polarization-dependent, the 3-dB channel-dropping bandwidth was 0.4 nm and the extinction ratio at the dropping wavelength for port THROUGH was better than 17 dB for assuming 1.6-nm wavelength spacing dense wavelength-division multiplexing. The average tuning speed was about 200 mu s.
Thermo-Optic Switch Based On 2d-Si Photonic Crystals

T Chu,H Yamada,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/GROUP4.2004.1416726

2004-01-01

Abstract:A Mach-Zehnder interferometer-type optic switch was firstly realized on Si photonic-crystal (PhC) slab structure, by using thermo-optic effect. The maximum extinction ratio was 22 dB, and the switching speed reached 200 mus.
Thermooptic Switch Based on Photonic-Crystal Line-Defect Waveguides

T Chu,H Yamada,S Ishida,Y Arakawa

DOI: https://doi.org/10.1109/lpt.2005.856357

IF: 2.6

2005-01-01

IEEE Photonics Technology Letters

Abstract:A thermooptic switch With a symmetric Mach-Zehnder interferometer structure was demonstrated with silicon photonic-crystal-slab line-defect waveguides. The device size was as small as 160 x 65 mu m. The optic switch operated at a wavelength of 1550 nm, and an extinction ratio greater than 30 dB was obtained by 120-mW heating (switching) power over the wavelength range of 15 nm. The switching ON-OFF response times were about 120 mu s.
Broadband Thermo-Optic Switch Based on a W2 Photonic Crystal Waveguide

Kaiyu Cui,Xue Feng,Yidong Huang,Qiang Zhao,Zhilei Huang,Wei Zhang

DOI: https://doi.org/10.1117/12.2004138

2013-01-01

Abstract:Broadband thermo-optic switch based on an ultra-compact W2 photonic crystal waveguide (PCW) is demonstrated with an integrated titanium/aluminum microheater on its surface. The operating principle relies on shifting a transmission-dip caused by the enhanced coupling between the defect modes in W2 PCW. As a result, broadband switching functionality with larger extinction ratio can be attained. Moreover, microheaters with different width are evaluated by the power consumptions and heating transfer efficiency, and an optimized slab microheater is utilized. Finally, switching functionality with bandwidth up to 24 nm (1557 similar to 1581 nm) is measured by the PCW with footprint of only 8. mx17.6 mu m, while the extinction ratio is in excess of 15 dB over the entire bandwidth. What's more, the switching speed is obtained by the measurement of alternating current modulation. Response time for this thermo-optic switch is 11.0 +/- 3.0 mu s for rise time and 40.3 +/- 5.3 mu s for fall time, respectively.
Temperature Tunable Photonic Band Gap Crystals Based on Liquid-Infiltrated Inverse Opal Structure

Zhendong Liu,Jingjing Gao,Bo Li,Ji Zhou

DOI: https://doi.org/10.1016/j.optmat.2012.11.013

IF: 3.754

2013-01-01

Optical Materials

Abstract:Temperature tunable photonic crystals were fabricated based on liquid-infiltrated inverse opal films. The photonic band gaps were investigated at different temperatures by reflection spectra. The results show that the photonic band gap can be tuned continuously by temperature change. In this work, the band gap was blue-shifted from 558 nm to 542 nm with increasing temperature from 28 °C to 48 °C. It will provide a new method of studying the modulation near edge effect of the photonic band gap.
Thermal tuning of band structures in a one-dimensional phononic crystal

Zuguang Bian,Wei Peng,Jizhou Song

DOI: https://doi.org/10.1115/1.4025058

2014-01-01

Abstract:Phononic crystals make the realization of complete acoustic band gaps possible, which suggests many applications such as vibration isolation, noise suppression, acoustic barriers, filters, wave guides, and transducers. In this paper, an analytic model, based on the transfer matrix method, is developed to study the band structures of bulk acoustic waves including SH-, P-, and SV-waves in a one-dimensional phononic crystal, which is formed by alternating strips of two different materials. The analysis is demonstrated by the phononic crystal of Ba0.7Sr0.3TiO3 (BST) and polybutylene terephthalate (PBT), whose elastic properties depend strongly on the temperature. The results show that some band gaps are very sensitive to the temperature. Depending on the wave mode, the center frequency of the first band gap may decrease over 25% and band gap width may decrease over 60% as the temperature increases from 30 degrees C to 50 degrees C. The transmission of acoustic waves in a finite phononic crystal is also studied through the coefficient of transmission power. These results are very useful for the design and optimization of thermal tuning of phononic crystals.
Fast Thermo-Optical Modulators with Doped-Silicon Heaters Operating at 2 Μm.

Chuyu Zhong,Hui Ma,Chunlei Sun,Maoliang Wei,Yuting Ye,Bo Tang,Peng Zhang,Ruonan Liu,Junying Li,Lan Li,Hongtao Lin

DOI: https://doi.org/10.1364/oe.430756

IF: 3.8

2021-01-01

Optics Express

Abstract:The 2-μm-waveband has been recognized as a potential telecommunication window for next-generation low-loss, low-latency optical communication. Thermo-optic (TO) modulators and switches, which are essential building blocks in a large-scale integrated photonic circuit, and their performances directly affect the energy consumption and reconfiguration time of an on-chip photonic system. Previous TO modulation based on metallic heaters at 2-μm-waveband suffer from slow response time and high power consumption. In this paper, high-performance thermo-optical Mach–Zehnder interferometer and ring resonator modulators operating at 2-μm-waveband were demonstrated. By embedding a doped silicon (p++-p-p++) junction into the waveguide, our devices reached a record modulation efficiency of 0.17 nm/mW for Mach–Zehnder interferometer based modulator and its rise/fall time was 3.49 μs/3.46 μs which has been the fastest response time reported in a 2-μm-waveband TO devices so far. And a lowest Pπ power of 3.33 mW among reported 2-μm TO devices was achieved for a ring resonator-based modulator.
Compact Thermo-Optic Switch Based on Tapered W1 Photonic Crystal Waveguide

Qiang Zhao,Kaiyu Cui,Zhilei Huang,Xue Feng,Dengke Zhang,Fang Liu,Wei Zhang,Yidong Huang

DOI: https://doi.org/10.1109/jphot.2013.2247993

IF: 2.4

2013-01-01

IEEE Photonics Journal

Abstract:A compact thermo-optic switch based on the cutoff effect of slow-light mode of a tapered W1 photonic crystal waveguide (PCW) is demonstrated with an integrated microheater. Due to the low-group-index taper, the coupling loss of the slow-light PCW is reduced, and a high switching extinction ratio (ER) is attained. Moreover, three types of microheaters are evaluated for the power consumptions, heating transfer efficiency, and temperature uniformities, and an optimized slab microheater is utilized. As a result, low switching power of 8.9 mW and high ER of 23.5 dB are achieved experimentally, while the length of W1 PCW is only 16.8 μm.
Thermo-optic Switch Based on Transmission-Dip Shifting in a Double-Slot Photonic Crystal Waveguide

Kaiyu Cui,Qiang Zhao,Xue Feng,Yidong Huang,Yongzhuo Li,Da Wang,Wei Zhang

DOI: https://doi.org/10.1063/1.4718353

IF: 4

2012-01-01

Applied Physics Letters

Abstract:Optical switch based on an ultra-compact double-slot photonic crystal waveguide (DS-PCWG) with a titanium/aluminum microheater is demonstrated. The operating principle relies on shifting a transmission-dip caused by the defect mode coupling in photonic band gap (PBG). Based on the unique mode coupling in PBG, low switching power of 9.2 mW and high extinction ratio of 17 dB are achieved experimentally while the length of DS-PCWG is only 16 μm.
Tuning of Photonic band gap via combined effect of electric and optical fields in a blue phase liquid crystal composite

N. Sharadhi,S. Vimala,K. Nurjahan,B. N. Veerabhadraswamy,C. V. Yelamaggad,Geetha G. Nair

DOI: https://doi.org/10.1080/02678292.2019.1640905

2019-07-31

Liquid Crystals

Abstract:Blue phase liquid crystals are soft 3D photonic crystals in which the liquid crystal molecules self-assemble to form a cubic structure with lattice spacing of a few hundred nanometers resulting in selective reflection of colours in the visible spectrum. The corresponding wavelength or the 'photonic band gap' can be tuned using various external stimuli such as thermal, electric, magnetic and optical fields. Here, we report efficient tuning of photonic band gap by utilising the combination of electric and optical fields in a blue phase liquid crystalline system. The studies indicate that the chirality of the medium has a direct bearing on the direction of the wavelength shift and the extent of the photonic band gap tunability. More importantly, the synergistic effect of the two fields helps in reversible tuning of the band gap.(Colour online)(Colour online)
All-optical Tunable Photonic Bandgap Microcavities with a Femtosecond Time Response

Xiaoyong Hu,Ping Jiang,Hong Yang,Qihuang Gong

DOI: https://doi.org/10.1364/ol.31.002777

2006-01-01

Abstract:An all-optical tunable photonic bandgap microcavity made from a two-dimensional polystyrene photonic crystal is fabricated by focused ion beam etching. The pump and probe scheme is adopted to measure tunability based on the femtosecond optical Kerr effect. An ultrafast response time of less than 120fs is achieved for the tunable photonic bandgap microcavity. The microcavity resonant wavelength shifts 3.1nm under excitation of 9.4GW/cm2 pump intensity, which is in agreement with the theoretical prediction.
Mechanical Tuning of the Terahertz Photonic Bandgap of 3D-Printed One-Dimensional Photonic Crystals

Serang Park,Brandon Norton,Glenn D. Boreman,Tino Hofmann

DOI: https://doi.org/10.1007/s10762-020-00763-6

2020-12-20

Abstract:Mechanical tuning of a 3D-printed, polymer-based one-dimensional photonic crystal was demonstrated in the terahertz spectral range. The investigated photonic crystal consists of 13 alternating compact and low-density layers and was fabricated through single-step stereolithography. While the compact layers are entirely polymethacrylate without any intentional internal structures, the low-density layers contain sub-wavelength sized slanted columnar inclusions to allow the mechanical compression in a direction normal to the layer interfaces of the photonic crystal. Terahertz transmission spectroscopy of the photonic crystal was performed in a spectral range from 83 to 124 GHz as a function of the compressive strain. The as-fabricated photonic crystal showed a distinct photonic bandgap centered at 109 GHz, which blue shifted under compressive stress. A maximum shift of 12 GHz in the bandgap center frequency was experimentally demonstrated. Stratified optical models incorporating simple homogeneous and inhomogeneous compression approximations were used to analyze the transmission data. A good agreement between the experimental and model-calculated transmission spectra was found.

Applied Physics,Optics
Thermally Switchable/tunable Photonic Integrated Devices on Silicon

Daoxin Dai,Sitao Chen,Longhai Yu,Yaocheng Shi

DOI: https://doi.org/10.1109/piers.2016.7734966

2016-01-01

Abstract:Thermo-optic effect plays an important role and has been paid intensive attention for realizing switchable/tunable photonic integrated devices. In particular, it is possible to realize energy-efficient thermally switchable/tunable photonic integrated devices on silicon because of the high thermo-optical coefficient of silicon material. Recently we realized silicon-based ultra-broadband low-loss thermo-optic switches realized by using an 2 × 2 Mach-Zehnder Interferometer (MZI) with bent directional couplers. This MZI switch is scaled to realize N × N thermo-optic switches and also integrated with arrayed-waveguide gratings for ultra-compact reconfigurable add-drop multiplexers. In order to improve the thermal-tuning/switching efficiency, a novel transparent graphene nano-heater, which contacts the silicon core region directly, is demonstrated experimentally. These recent progress for thermally switchable/tunable photonic integrated devices on silicon is reviewed in this paper.
Dynamic Epsilon-Near-Zero Wavelength Tuning and Switching Properties of Hyperbolic Metamaterials

Ze Tao Xie,Jiaye Wu,Yanhua Sha,H. Y. Fu,Qian Li

DOI: https://doi.org/10.1364/acpc.2021.t4a.173

2021-01-01

Abstract:We demonstrate the tuning of the epsilon-near-zero wavelength from telecommunication to mid-infrared regime in hyperbolic metamaterials by pump excitation. The structure has a dynamic switching modulation of up to 8.4 dB.
Ultracompact Variable Optical Attenuator Based on Photonic Crystal Waveguide

Qiang Zhao,Kaiyu Cui,Yidong Huang

DOI: https://doi.org/10.1117/12.904382

2011-01-01

Abstract:We demonstrated and fabricated a 20μm-long ultra-compact variable optical attenuator based on thermo-optical effect with slow light photonic crystal waveguide (PCWG). In simulation, we optimize the line-defect width and radius/period ratio (r/a) of the PCWG for deep photonic band gap and large slope photonic band edge. An r/a=140nm/410nm W1 PCWG is selected for its -60dB depth and 36dB variable attenuation range when the tunable refractive index change is 0.01. We also study different shapes of micro-heaters for low power consumption and high heat transfer efficiency. A 24.6mW and 75.9% heat transfer efficiency are achieved in a 2μm-wide right-angle-shaped micro-heater. In experiment, A 4.6nm red shift at the cutoff wavelength of the fundamental mode and a 10dB tunable attenuation range are achieved through tuning the temperature of the W1 PCWG by an 4.7μm-wide aluminum micro-heater with a maximum power consumption as low as 30.7mW.
Silicon Optical Switch Based On A Tapered W1 Photonic Crystal Waveguide With Thermo-Optic Effect

Qiang Zhao,Kaiyu Cui,Zhilei Huang,Xue Feng,Dengke Zhang,Yidong Huang

DOI: https://doi.org/10.1364/cleo_at.2013.jtu4a.35

2013-01-01

Abstract:Thermo-optic switch based on W1 photonic crystal waveguide is demonstrated, high extinction ratio of 23.5 dB has been experimentally achieved under a switching power as low as 8.9 mW while the device is only 16.8-mu m-long.
Tunable 1D nano-photonic filter using Nematic liquid crystal and high-Tc superconductors

Y. Trabelsi,N. Ben Ali,Francis Segovia-Chaves,Herbert Vinck Posada

DOI: https://doi.org/10.1007/s11082-021-03275-2

IF: 3

2021-11-15

Optical and Quantum Electronics

Abstract:In this paper, the properties of hybrid photonic band gaps (PBGs) has been theoretically investigated using the transfer matrix method (TMM) and Gorter Casimir two-fluid model. These 1D photonic quasicrystals are built using the hybrid materials (Bi,Pb)2Sr2Ca2Cu3Ox/anisotropic Nematic liquid crystal layers. Based on the simulation results, a tunable PBG can be achieved within the transmission spectrum with sub comb-like resonant peaks at regular temperature of high Tc superconductor. The PBG properties and the number of resonant peaks are directly modulated by the superconductor temperature, the thickness of the dielectric layers and the lattice parameters of the quasi-periodic structure. In addition, the dependence of the PBGs on the temperature of the Nematic liquid crystal is discussed. The behavior of PBGs undergoing mechanical deformation for both polarization modes and in the presence of an external applied voltage is discussed. These structures can serve as tunable optical stop-band-gap-filters in photonic integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology

Photonic Bandgap Tuning With Thermo-Optic Effect

Temperature-controlled transformation in fiber types of fluid-filled photonic crystal fibers and applications.

Tunable Optical Notch Filter Realized by Shifting the Photonic Bandgap in a Silicon Photonic Crystal Line-Defect Waveguide

Controlling the photonic bandgap structures via manipulation of refractive index of electromagnetically induced transparency vapor

Tunable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguides

Thermo-Optic Switch Based On 2d-Si Photonic Crystals

Thermooptic Switch Based on Photonic-Crystal Line-Defect Waveguides

Broadband Thermo-Optic Switch Based on a W2 Photonic Crystal Waveguide

Temperature Tunable Photonic Band Gap Crystals Based on Liquid-Infiltrated Inverse Opal Structure

Thermal tuning of band structures in a one-dimensional phononic crystal

Fast Thermo-Optical Modulators with Doped-Silicon Heaters Operating at 2 Μm.

Compact Thermo-Optic Switch Based on Tapered W1 Photonic Crystal Waveguide

Thermo-optic Switch Based on Transmission-Dip Shifting in a Double-Slot Photonic Crystal Waveguide

Tuning of Photonic band gap via combined effect of electric and optical fields in a blue phase liquid crystal composite

All-optical Tunable Photonic Bandgap Microcavities with a Femtosecond Time Response

Mechanical Tuning of the Terahertz Photonic Bandgap of 3D-Printed One-Dimensional Photonic Crystals

Thermally Switchable/tunable Photonic Integrated Devices on Silicon

Dynamic Epsilon-Near-Zero Wavelength Tuning and Switching Properties of Hyperbolic Metamaterials

Ultracompact Variable Optical Attenuator Based on Photonic Crystal Waveguide

Silicon Optical Switch Based On A Tapered W1 Photonic Crystal Waveguide With Thermo-Optic Effect

Tunable 1D nano-photonic filter using Nematic liquid crystal and high-Tc superconductors