Abstract:With the fast growth in emerging technologies for mobile applications, packaging solutions are being driven by advanced Silicon (Si) nodes technology (down to 7nm), smaller form factor package designs, efficiency enhancement and lower power consumption. The flip chip chip scale package (fcCSP) has been widely adopted as the solution for mobile devices to satisfy these challenging requirements. In order to create a lower cost solution, the fcCSP uses the cost-effective combination of copper (Cu) pillar bumps, embedded trace substrate (ETS) technology, mass reflow (MR) chip attach and molded underfill (MUF) processes. Although the utilization of MR chip attach is a cost-effective process for flip chip package assembly, there is a high risk for a bump to trace short, especially for the designs with finer bump pitch and line width / line spacing (LW/LS) with an escaped trace. To reduce this risk, the laser assisted bonding (LAB) methodology is introduced to study the 7nm chip-package interaction (CPI) of an fcCSP with a 60µm bump pitch and escaped traces design in this paper. For the purpose of measuring the extremely low-k (ELK) performance in a 14x14mm fine pitch fcCSP with 7nm live die, the thunder test (two-times MR and quick temperature cycling (QTC) tests) as well as the hammer test with multi-reflow process (peak temperature at 260ºC) have been evaluated after performing LAB and MR chip attach methodologies. The results show that although both chip attach methodologies can pass the normal requirements of the thunder and hammer tests, the utilization of LAB technology can further enhance the strength of ELK and produce better yield performance. From these results, it is believed that LAB not only can guarantee assembly yield with less ELK damage risk in the examined 7nm fcCSP, but can also accommodate Si node and bump pitch reduction with a finer LW/LS substrate with escaped traces design.

Laser Ink-Jet Solder Bump Fabrication for Electronic Interconnection

Study of Stencil Printing Technology for Fine Pitch Flip Chip Bumping

A Study on Improvement and Extension of Fine-Pitch Micro-Bump Interconnects Technology: New Metallurgy & Flux-Less Oxide-removal Laser Assembly (FLOLA)

Characterization of stencil printing parameters for fine pitch wafer bumping

The Research on a Low Cost Flip Chip Bumping Process by Stencil Printing

Eco-Friendly Lead-Free Solder Paste Printing via Laser-Induced Forward Transfer for the Assembly of Ultra-Fine Pitch Electronic Components

Seed Layer Etching, Thermal Reflow and Bonding of Cu-Sn Micro Bumps with 5 Μm Diameters

Fabrication of Fine-Pitch Cu-Sn Microbumps Using Electroplating and Wet Seed Layer Etching

Cu–Cu Bonded Microbump Interconnects with a 10- $\mu$ M Pitch for 3-D-stacked Chiplets

Self-sintering liquid metal ink with LAPONITE? for flexible electronics

Characterization of sintered Cu nanopaste for micro-bumping with Injection Molded Solder technology

Effect of Different Material Systems on Interconnection Properties of 30μm Pitch Micro Bumps

Laser direct printing of solder paste

Fabrication and Mechanical Properties Improvement of Micro Bumps for High-Resolution Micro-LED Display Application

Ultrasonic‐Enabled Nondestructive and Substrate‐Independent Liquid Metal Ink Sintering

7nm Chip-Package Interaction Study on a Fine Pitch Flip Chip Package with Laser Assisted Bonding and Mass Reflow Technology

Design and Experiment of a Solder Paste Jetting System Driven by a Piezoelectric Stack

Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking

Micro-Cantilever Array With Electroplating Tin Bumps for Flip-Chip Bonding Technology

Fine-pitch bonding technology with surface-planarized solder micro-bump/polymer hybrid for 3D integration

Tin Bumping for Wafer Level Lead-Free Packaging