1-V and 10-V Josephson junction array voltage standard at NIM

Xue, S.Q.,Zhang, J.,Zhou, Y.Q.,Li, H.H.

DOI: https://doi.org/10.1109/CPEM.1994.333435

1994-01-01

Abstract:A group of standard cell can be calibrated simultaneously and safely by the JJAVS via a Hg-Zn cell based dc voltage reference in three minutes. The total uncertainty of 8/spl times/10/sup -9/ and 5/spl times/10/sup -9/ are achieved at 1.018 V and 10 V level for Zener reference.<>

What problem does this paper attempt to address?

The Research Progress of the Josephson Array Device

Xiao-wei GUO,Zong-Tao CHI,Wen-hui CAO,Qing Zhong,Qing HE,Jin-jin LI

DOI: https://doi.org/10.3969/j.issn.1000-1158.2013.04.15

2013-01-01

Abstract:The application of the Josephson effect used for voltage standards is introduced. The development of the Josephson array in the field of voltage standard and the current research status of the Josephson array at home and abroad are summarized. Furthermore, the research progress of the Nb/NbxSi1-x/Nb junction used for voltage standard in domestic is introduced with emphasis.
Feasibility of the Josephson voltage and current standards on a single chip

Rais S. Shaikhaidarov,Ilya Antonov,Kyung Ho Kim,Artem Shesterikov,Sven Linzen Evgeni V. Il'ichev,Vladimir N. Antonov,Oleg V. Astafiev

DOI: https://doi.org/10.1063/5.0221404

2024-10-15

Abstract:The quantum Josephson voltage standard is well established across the metrology community for many years. It relies on the synchronisation of the flux tunneling in the S/I/S Josepson junctions (JJ) with the microwave radiation (MW). The phenomenon is called the Shapiro steps. Together with the Quantum Hall resistance standard, the voltage standard forms the foundation of electrostatic metrology. The current is then defined as the ratio of the voltage and resistance. Realisation of the quantum current standard, would close the electrostatic metrological triangle of voltage-resistance-current. The current quantisation, the inverse Shapiro steps, was recently shown using the superconducting nanowires and small JJ. The effect is a synchronization of the MW with the Cooper pair tunnelling. This paves the way to combine the JJ voltage and current standards on the same chip and demonstrate feasibility of the multi-standard operation. We show the voltage and current quantization on the same chip up to frequency of 10 GHz, corresponding to the amplitudes 0.021 mV and 3.23 nA respectively. The accuracy of the voltage and current quantisation, however, is relatively low, 35 ppk and 100 ppk respectively. We discuss measures to optimise the JJs, circuit and environment to boost the amplitude and accuracy of the standards.

Superconductivity
Comparison of the Josephson voltage standards of the NIM (China) and the BIPM

D Reymann,S Q Xue,R M Liu,H H Li,J Gao,Y Q Zhou,T J Witt

DOI: https://doi.org/10.1088/0026-1394/33/5/6

1996-01-01

Metrologia

Abstract:Comparisons of the 1 V Josephson array voltage standard of the Bureau International des Poids et Mesures (BIPM) were made with that of the National Institute of Metrology (NIM), Beijing, China, in November 1995. The results agree within an overall uncertainty of less than 1 nV.
High Tc Harmonic Mixer Applied to Josephson Junction Array Voltage Standard at NIM

SQ Xue,HH Li,XC Shen,HB Wang,WW Xu,QH Cheng,PH Wu

DOI: https://doi.org/10.1109/19.571824

1996-01-01

Abstract:Summary form only given, as follows.High Tc superconducting (YBCO) Josephson junction harmonic mixer has been used to improve the spectrum purity of the microwave source in the JJAVS at NIM. Compare with the microwave source using source locking counter EIP 578B, the spectrum purity of the microwave source has been improved significantly from -25 dBc/Hz (offset /spl plusmn/500 kHz) to -58 dBc/Hz (offset /spl plusmn/10 kHz). Therefore, the uncertainty of the JJAVS was reduced.
Fabrication and Characterization of Nb/Nb<inf>x</inf>Si<inf>1&#x2212;x</inf>/Nb Josephson Junction Arrays for Voltage Standard

Wenhui Cao,Jinjin Li,Yuan Zhong,Yonggang Liu,Qing He

DOI: https://doi.org/10.1109/cpem.2014.6898286

2014-01-01

Abstract:We report in CPEM 2014 our effort towards SNS Josephson junction devices for the quantum voltage standard. SNS junction array device, with Nb as the superconductor material (S) and Nb x Si 1-x alloy as the barrier material (N), is fabricated and tested by NIM (National Institute of Metrology). The I-V characteristic curves of the junction arrays are measured and the experimental results are discussed.
The Status of AC Quantum Voltage Standards

ZHOU Kun-li,QU Ji-feng,ZHANG Zhong-hua,ZHAO Wei

DOI: https://doi.org/10.3969/j.issn.1000-1158.2017.04.22

2017-01-01

Abstract:Compared to the conventional voltage standards, Josephson voltage standards are more reproducible, stable and accurate. The principles, problems and applications of programmable Josephson voltage standards and pulse-driven AC Josephson voltage standards are reviewed.Moreover, their differences in metrological performance are compared and their developments in China are also presented.
Josephson Voltage Standard Circuit Operation with a Pulse Tube Cooler

G Wende,M Schubert,T May,L Fritzsch,HG Meyer,G Thummes,Y Kucukkaplan,LM Qiu,J Kohlmann,J Niemeyer,H Hofmeister,J Scheerer

DOI: https://doi.org/10.1109/tasc.2003.814081

IF: 1.9489

2003-01-01

IEEE Transactions on Applied Superconductivity

Abstract:For a more wide-spread use of Josephson voltage standards, cryogen-free operation, by means of an appropriate closed-cycle refrigerator, is highly desirable. In this work we present a low-noise pulse tube cooler (PTC) that is capable to cool the voltage standard circuits to temperatures below 4 K.As a low loss dielectric waveguide with a very small thermal conductivity a Teflon strip was used for the microwave transmission. The matched transition from the WR12 rectangular waveguide to the Teflon strip and vice versa was made using special exponential tapers.Programmable 1 Volt 14 bit SINIS and 10 Volt SIS arrays assembled in the PTC operated well, i.e., demonstrated a similar performance to that measured in liquid helium. The Josephson junction arrays were integrated in coplanar strips instead of the commonly used microstriplines for the microwave transmission lines.The 1 Volt SINIS array contained 8,192 Josephson junctions (JJ's). It generated an inherently stable Josephson voltage step of 1.19 V at a driving microwave frequency of 70 GHz. The step width was 150 muA and the critical current of the junctions was 550 muA. Similar results were obtained under liquid helium cooling conditions. In another experiment a 10 Volt voltage standard chip with 19,700 SIS JJ's was installed. It was possible to generate stable Shapiro steps at the 10 V level.
Fabrication and characterization of physically-linked large-scale josephson junction test arrays

Lanruo Wang,Jinjin Li,Wenhui Cao,Yuan Zhong,Xueshen Wang,Qing Zhong

DOI: https://doi.org/10.1109/cpem.2018.8543119

2018-01-01

Abstract:The efforts of National Institute of Metrology (NIM) towards large scale Nb/ Nb x Si1- x /Nb Josephson junction arrays for the quantum voltage standards are presented in this paper. Physically-linked arrays with 10,000 and 20,000 junctions (corresponding to 1 and 2 junctions vertically) are fabricated. DC I-V characteristics of different stacked arrays are measured and experimental results are discussed. Focusing ion beam (FIB) together with scanning electron microscope (SEM) are used to examine the cross-section of three types of junction stacks which vertically contains 2, 3, and 4 junctions respectively. It is shown that grain boundary defects in the niobium wiring layer exist for all of these junction stacks. A method which potentially could solve this problem is proposed.
Development of Quantum Voltage Noise Source Chip for Precision Measurement of Boltzmann Constant

Wang Lan-Ruo,Zhong Yuan,Li Jin-Jin,Qu Ji-Feng,Zhong Qing,Cao Wen-Hui,Wang Xue-Shen,Zhou Zhi-Qiang,Fu Kai,Shi Yong

DOI: https://doi.org/10.7498/aps.67.20172643

IF: 0.906

2018-01-01

Acta Physica Sinica

Abstract:The Johnson noise thermometer is used to precisely measure Boltzmann constant by comparing the thermal noise caused by charge movement and the quantized voltage reference noise synthesized by the quantum voltage noise source (QVNS). The QVNS signal is synthesized based on quantized voltage pulses produced by two channels of superconducting Josephson junction arrays, which are designed for cross-correlation electronics. The Nb/NbxSi1-x/Nb Josephson junction is used as a core device of QVNS chip in this work for its non-hysteretic current-voltage (I-V) characteristics and conveniently adjustable barrier parameters.In this paper, we present the design consideration, fabrication process, and measurement results of the QVNS chip. The QVNS chip contains two Josephson junction arrays, each consists of four 6 μm×12 μm junctions and is embedded in a 50 Ω coplanar waveguide transmission line. The random noise in signals from the two driven channels is eliminated by cross-correlation, and then an accurate quantum noise is obtained. Test chips with different areas of Josephson junctions are also designed on the same mask, aiming at estimating the variation range of Ic. The typical fabrication process for voltage standard chips in our laboratory is used for preparing the QVNS chip.The sample is measured at 4.2 K. The DC I-V curve shows that the critical current Ic is 6.1 mA. The I-V characteristics of the junctions under 5 GHz microwave radiation are measured. For a series array of four junctions, a 41.44 μV one-stage Shapiro step is observed. Calculation shows that the error between the measurement and theoretical value of 41.36 μV is about 1.9‰, which means that the QVNS chip performs well under microwave radiation and can be used for synthesizing the AC quantum voltage reference noise.A single-frequency 100 kHz sinusoidal waveform is synthesized by the QVNS chip under pulse driven signal. A spectrum of the synthesized sinusoidal waveform shows a single peak, which means that the digital pulse signal is perfectly filtered by Josephson junction arrays and the synthesized signals possess quantum accuracy. The results indicate that our chip has good dynamic response and works well in synthesizing a single-frequency AC quantum voltage signal. This work can provide core devices for the noise thermometry system and support the precise measurement of Boltzmann constant as well as redefinition of Kelvin in future. As a next step, the design and package will be further improved, and the probe module will be optimized to reduce the measurement uncertainty.
Two-Volt Josephson Arbitrary Waveform Synthesizer Using Wilkinson Dividers

Nathan E Flowers-Jacobs,Anna E Fox,Paul D Dresselhaus,Robert E Schwall,Samuel P Benz

DOI: https://doi.org/10.1109/TASC.2016.2532798

Abstract:The root-mean-square (rms) output voltage of the NIST Josephson arbitrary waveform synthesizer (JAWS) has been doubled from 1 V to a record 2 V by combining two new 1 V chips on a cryocooler. This higher voltage will improve calibrations of ac thermal voltage converters and precision voltage measurements that require state-of-the-art quantum accuracy, stability, and signal-to-noise ratio. We achieved this increase in output voltage by using four on-chip Wilkinson dividers and eight inner-outer dc blocks, which enable biasing of eight Josephson junction (JJ) arrays with high-speed inputs from only four high-speed pulse generator channels. This approach halves the number of pulse generator channels required in future JAWS systems. We also implemented on-chip superconducting interconnects between JJ arrays, which reduces systematic errors and enables a new modular chip package. Finally, we demonstrate a new technique for measuring and visualizing the operating current range that reduces the measurement time by almost two orders of magnitude and reveals the relationship between distortion in the output spectrum and output pulse sequence errors.
Design of a Dual-Channel Josephson Array Test System

MA Mengze,CAO Wenhui,LI Jinjin,XU Da,WANG Shijian,GAO He,ZHONG Qing,ZHONG Yuan

DOI: https://doi.org/10.12338/j.issn.2096-9015.2023.0023

2023-01-01

Abstract:In response to the growing demand for chip testing, a dual-channel Josephson array test system was designed, incorporating key components such as low-temperature test probes and microwave transmission structures. The test system enables simultaneous measurement of two programmable Josephson devices and provides superimposed voltage output of the two chips. The system's functionalities were validated by measuring a dual-channel programmable Josephson device. The optimal operating frequency of the device is 17 GHz, with an operating power of 11 dBm without a power amplifier. For the dual-channel small voltage programmable Josephson device, the minimum array consists of 1 junction with an output voltage of 35.15 μV, and the maximum array contains 512 junctions with an output voltage of 17998.42 μV. The broadening range of quantum voltage steps is 2 μV. This is due to 34420A (1 V range) noise and testing system noise, which meets the requirements of quantum voltage testing.The dual-channel quantum voltage output is 70.30 μV for a single junction and 35996.84 μV for 512 junctions, the broadening range of quantum voltage steps after superposition is also within 2 μV. This demonstrates that the dual-channel Josephson array test system can not only measure two independent programmable chips but also achieve quantum voltage superimposed output without increasing process difficulty.
A 3 Mm Waveband Gunn Oscillator Phase-Locked with a High- Josephson Harmonic Mixer and Its Applications to the Quantum Voltage Standard

H B Wang,Wei Xu,Qilin Cheng,Peiheng Wu,S.Q. Xue,H,Xuwei Shen

DOI: https://doi.org/10.1088/0022-3727/30/2/015

1997-01-01

Abstract:Using a high- superconducting harmonic mixer at 77 K and a phase-locking loop, a signal source (a Gunn oscillator in the 3 mm waveband) was directly phase-locked to a local oscillator for frequencies less than 1 GHz and harmonic numbers up to 120. The phase-locked Gunn oscillator achieved a frequency instability of less than Hz, with the counting time of 1 s, while the phase noise at intermediate frequency 40 MHz was ( kHz) for 120th harmonic mixing and ( kHz) for 42nd harmonic mixing. The output of this phase-locked signal source was applied to a Josephson junction array used in a voltage-standard system against which a solid-state voltage source (a Zener voltage reference) was measured. The experimental results showed that the quality of this phase-locked microwave source was good enough to justify its use in the quantum voltage standard.
Research on Automatic Verification of Standard Cell

HU Yi-fei,KANG Yan,ZHAO Wei

DOI: https://doi.org/10.3969/j.issn.1001-1390.2006.12.001

2006-01-01

Abstract:The method of automatic verification of high grade standard cell is introduced. The precise air-trough is adopted in which the temperature could be controlled to maintain standard cell.The low thermal EMF programmable control switch is used to choice the mea- surement channels and reversion.The difference of voltage is measured by digital nano- voltmeter.Using Zener reference standards verifying by Josephson voltage standard as work- ing standard the system is not only achieved the automatic calibration of standard cell by program edited by VB software,and also trace to the source of direct current voltage of na- tional secondary standard.
A primary quantum current standard based on the Josephson and the quantum Hall effects

Sophie Djordjevic,Ralf Behr,W. Poirier

2024-07-17

Abstract:The new definition of the ampere calls for a quantum current standard able to deliver a flow of elementary charges per second controlled with a relative uncertainty of one part in $10^8$. Despite many efforts, nanodevices handling electrons one by one have never been able to demonstrate such an accuracy. The alternative route based on applying Ohm's law to the Josephson voltage and quantum Hall standards recently reached the target uncertainty but this was at the expense of the application of error corrections, hampering simplicity and further improvement. As a result, national metrology institutes still lack an operational quantum current standard. Here, we present a new quantum current generator, combining both quantum standards and a superconducting cryogenic amplifier, free of error correction, which provides quantized currents driven by the Josephson microwave signal. We show that it can realize the ampere definition with the target uncertainty over a range extended from mA down to $\mu$A and improve end-user current measurements, which are up to now a hundred times less accurate. Other prospects include measuring large resistances using the new current standard in conjunction with a quantum voltmeter and, by exploiting its low-noise performances, bridging the gap with the lower currents of other quantum current sources.

Mesoscale and Nanoscale Physics,Other Condensed Matter,Instrumentation and Detectors,Quantum Physics
A Study of Calibration System of DC Digital Nanovoltmeter

HU Yi-fei,ZHAO Wei,ZHU Zhu,KANG Yan,HUANG Jing,LI Xiao-yan

DOI: https://doi.org/10.3321/j.issn:1000-1158.2007.01.002

2007-01-01

Abstract:Based on the low thermal EMF divider,a low DC voltage calibration system is developed for DC digital nanovoltmeter calibration.To reduce thermal EMF in measurement circuit,the techniques of connection among cables by special press and temperature-controlled box are studied.The Hamon junctions are fabricated in order to reduce resistance of the leads.The symmetric observation method and linear interpolation method are put forward to reduce the influence of thermal EMF by one order of magnitude.The low DC voltage calibration system shows measuring range from 1 μV to 100 mV,and measurement uncertainty of 2.2% at 1 μV value.
The Measurement System of Statistical Distribution of the Switching Current of a Single Josephson Junction

Ying WANG,Wei-wei XU,Guo-zhu SUN,Jian CHEN,Jun-yu CAO,Shan-hua CONG,Pei-heng WU

DOI: https://doi.org/10.3321/j.issn:0372-2112.2007.05.005

2007-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:A system, which measures the statistical distribution of the switching current of a single Josephson junction (JJ) based on time-resolved measurement, is introduced. This system includes both the refrigeration system and the measurement method. Moreover, we tried several techniques to reduce the noise, such as electromagnetic shielding, low-pass filter and ground connection, and the lowest equivalent temperature of JJ in the experiment was reduced to 300 mK.
Standard measurement method for normal state resistance and critical current of resistively shunted Josephson junctions

M Ohkubo,G Uehara,J Beyer,M Mimura,H Tanaka,K Ehara,S Tanaka,T Noguchi,E E Mitchell,C P Foley,R L Fagaly

DOI: https://doi.org/10.1088/1361-6668/ac4f3b

2022-02-14

Superconductor Science and Technology

Abstract:Abstract An important parameter of Josephson junctions (JJs) is the product of normal state resistance ( R n ) and critical current ( I c ) for designing superconductor analogue devices or digital circuits. Determination of R n and I c from voltage – current ( U–I ) characteristic curves often faces difficulties; in particular I c is considerably reduced by intrinsic thermal or extrinsic electrical noises. Here, we propose a standard measurement method of R n and intrinsic critical current ( I ci ) for high- T c superconductor (HTS) grain boundary JJs operated in liquid nitrogen and low- T c superconductor (LTS) multilayer superconductor/normal-conductor/superconductor (SNS) JJs in liquid helium. The applicable condition of this method is that both HTS and LTS JJs have U–I curves compatible with resistively-shunted junction (RSJ) model. Both R n and I ci values are extracted by combining a geometric mean criterion to select a data set and a least-squares fitting method with the RSJ model, eliminating two distortion effects on U–I curves: noise-rounding and self-heating. The combined method ensures relative standard uncertainty values of 1.9% for R n and 8% for I ci or better, when the users follow the standard protocol. It is demonstrated that the combined method is valid for d -wave HTS JJs near 77 K, regardless of peculiarities such as 0– π junction transition in d -wave superconductors at lower temperatures, and s -wave LTS SNS JJs with a wide range of junction parameters. This work is the first step to facilitate standardization for superconductor electronics with JJs.

physics, condensed matter, applied
300 Mv Josephson Arbitrary Waveform Synthesizer Chip in NIM

Yuan Zhong,Qing Zhong,Cao Wenhui,Jinjin Li,Kunli Zhou,Jifeng Qu

DOI: https://doi.org/10.1109/cpem61406.2024.10645987

2024-01-01

Abstract:This paper describes the current status of developing Josephson arbitrary waveform synthesizer (JAWS) chips in NIM (National Institute of Metrology, China). The chip has one data input channel and two Josephson junction arrays, each array consisted by 4000 double-stack Nb/Nb x Si 1–x /Nb junctions. The two arrays were driven with a single pulse-generator channel by using one on-chip Wilkinson power divider and inside/outside DC blocks. Root-mean-square (rms) output magnitude of 300 mV was generated with this JAWS chip.
The Progress of Joule Balance

Zhong-hua ZHANG,Chen LI,Qing HE,Zheng-kun LI,Bing HAN,Yun-feng LU,Jiang LAN,Shi-song LI,Ya-qiong FU,Gang WANG

DOI: https://doi.org/10.3969/j.issn.1000-1158.2014.04.01

2014-01-01

Abstract:The National Institute of Metrology(NIM)has been studying the Joule Balance method(which is used for the same purpose as the Watt Balance method but operated differently),for several years to establish a kind of quantum mass standard by means of measuring the Planck constant. Since 2010,some progress has been achieved. A new standard square wave compensation method has been developed to measure the DC mutual inductance with an uncertainty of several parts in 10 - 7(k = 1). . An eddy current sensor for positioning has been designed and implemented to obtain a more accurate position of the movable coil. . The alignment technique for the coil system has also been placed under consideration. Specifically,a newly developed oil damping device reduces the small swing of the coil set(which occurs because of a combination of the weak vibration of the balance base and the hot ascending warm air from the current heating of coils). As a result,the measurement uncertainty of the coil position and mutual inductance is improved. . The recent measurement result of the Planck constant h is 6. 626104(59)× 10 - 34 J·s with an uncertainty of 8. 9 × 10 - 6( k = 1). Further improvements and difficulties are also discussed.
Recent Development on the Joule Balance at NIM

Zhonghua Zhang,Qing He,Zhengkun Li,Yunfeng Lu,Jianting Zhao,Bing Han,Yaqiong Fu,Chen Li,Shisong Li

DOI: https://doi.org/10.1109/tim.2011.2113930

IF: 5.6

2011-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:The precise measurement of Planck constant h to establish a kind of quantum mass standard is an important but very difficult work. The Joule Balance method, for the same purpose but different from Watt Balance method, has been going on at the National Institute of Metrology for three years. All the measurements were carried out in the atmosphere of an air-conditioned room. The uncertainty is several parts in 104 (k=1) and expected to be improved when superconducting coils and other approaches are used further. The principle and progress are described here.

1-V and 10-V Josephson junction array voltage standard at NIM

The Research Progress of the Josephson Array Device

Feasibility of the Josephson voltage and current standards on a single chip

Comparison of the Josephson voltage standards of the NIM (China) and the BIPM

High Tc Harmonic Mixer Applied to Josephson Junction Array Voltage Standard at NIM

Fabrication and Characterization of Nb/Nb&lt;inf&gt;x&lt;/inf&gt;Si&lt;inf&gt;1&amp;#x2212;x&lt;/inf&gt;/Nb Josephson Junction Arrays for Voltage Standard

The Status of AC Quantum Voltage Standards

Josephson Voltage Standard Circuit Operation with a Pulse Tube Cooler

Fabrication and characterization of physically-linked large-scale josephson junction test arrays

Development of Quantum Voltage Noise Source Chip for Precision Measurement of Boltzmann Constant

Two-Volt Josephson Arbitrary Waveform Synthesizer Using Wilkinson Dividers

Design of a Dual-Channel Josephson Array Test System

A 3 Mm Waveband Gunn Oscillator Phase-Locked with a High- Josephson Harmonic Mixer and Its Applications to the Quantum Voltage Standard

Research on Automatic Verification of Standard Cell

A primary quantum current standard based on the Josephson and the quantum Hall effects

A Study of Calibration System of DC Digital Nanovoltmeter

The Measurement System of Statistical Distribution of the Switching Current of a Single Josephson Junction

Standard measurement method for normal state resistance and critical current of resistively shunted Josephson junctions

300 Mv Josephson Arbitrary Waveform Synthesizer Chip in NIM

The Progress of Joule Balance

Recent Development on the Joule Balance at NIM

Fabrication and Characterization of Nb/Nb<inf>x</inf>Si<inf>1−x</inf>/Nb Josephson Junction Arrays for Voltage Standard