Feasibility of the Josephson voltage and current standards on a single chip

Rais S. Shaikhaidarov,Ilya Antonov,Kyung Ho Kim,Artem Shesterikov,Sven Linzen Evgeni V. Il'ichev,Vladimir N. Antonov,Oleg V. Astafiev
DOI: https://doi.org/10.1063/5.0221404
2024-10-15
Abstract:The quantum Josephson voltage standard is well established across the metrology community for many years. It relies on the synchronisation of the flux tunneling in the S/I/S Josepson junctions (JJ) with the microwave radiation (MW). The phenomenon is called the Shapiro steps. Together with the Quantum Hall resistance standard, the voltage standard forms the foundation of electrostatic metrology. The current is then defined as the ratio of the voltage and resistance. Realisation of the quantum current standard, would close the electrostatic metrological triangle of voltage-resistance-current. The current quantisation, the inverse Shapiro steps, was recently shown using the superconducting nanowires and small JJ. The effect is a synchronization of the MW with the Cooper pair tunnelling. This paves the way to combine the JJ voltage and current standards on the same chip and demonstrate feasibility of the multi-standard operation. We show the voltage and current quantization on the same chip up to frequency of 10 GHz, corresponding to the amplitudes 0.021 mV and 3.23 nA respectively. The accuracy of the voltage and current quantisation, however, is relatively low, 35 ppk and 100 ppk respectively. We discuss measures to optimise the JJs, circuit and environment to boost the amplitude and accuracy of the standards.
Superconductivity
What problem does this paper attempt to address?
This paper aims to solve the feasibility problem of how to realize the Josephson voltage standard and current standard on the same chip. Specifically, the author attempts to combine these two quantum standards to form an integrated chip that can provide high - precision voltage and current measurements simultaneously. ### Research Background 1. **Josephson Voltage Standard**: It has been widely used in the field of metrology. By synchronizing the magnetic flux tunneling in the superconductor - insulator - superconductor (S/I/S) Josephson junction (JJ) with microwave radiation (MW), the quantization of voltage is realized. The formula is: \[ V=\frac{\Phi_0 f}{m}\quad(m = 0,1,2,\ldots) \] where $\Phi_0=\frac{h}{2e}$ is the magnetic flux quantum, $f$ is the microwave frequency, and $m$ is an integer. 2. **Josephson Current Standard**: Recent research shows that by synchronizing microwaves with Cooper pair tunneling, the quantization of current can be realized in superconducting nanowires and small Josephson junctions. The formula is: \[ I = 2efm \] ### Research Objectives The goal of the paper is to integrate these two quantum standards on the same chip and verify their feasibility. Specifically: - **Experimental Verification**: The quantization of voltage and current has been realized on a single chip, with the highest frequency reaching 10 GHz, the corresponding voltage amplitude being approximately 20.67 µV, and the current amplitude being approximately 3.23 nA. - **Accuracy Evaluation**: The current accuracies of voltage and current quantization are 35 ppk and 100 ppk respectively, which are relatively low. - **Optimization Measures**: Several methods for improving the performance of JJ, circuits, and the environment to enhance the quantization accuracy are discussed, including using more advanced materials (such as Nb), improving circuit design, and optimizing the experimental environment, etc. ### Main Findings - **Direct and Inverse Shapiro Steps**: Direct Shapiro steps (voltage quantization) and inverse Shapiro steps (current quantization) were observed in Josephson junctions with different parameters respectively. - **Accuracy Challenges**: Although integration has been achieved, the accuracy of the current standard is much lower than that of the voltage standard, mainly limited by the low CQPS energy and environmental noise. ### Future Development Directions The author proposes several improvement measures to enhance the quantization accuracy, including: 1. **Material Selection**: Use materials with a larger superconducting energy gap (such as Nb) to increase CQPS energy. 2. **Circuit Design**: Improve circuit design to reduce noise interference, for example, by adopting a pure voltage - bias scheme. 3. **Environment Optimization**: Reduce the temperature through techniques such as immersion cooling to reduce the influence of thermal noise. In conclusion, this research demonstrates the feasibility of integrating Josephson voltage and current standards on the same chip and provides directions for further optimization.