Abstract:Design of non-transferred DC electric arc plasma torches (EAPTs) operated with plasma gases containing alkane hydrocarbons, as a promising type of heaters for a number of technologies (thermal spraying, surface hardening, testing of thermal protection systems, etc.), requires taking into account the evaporation rate of surface cathode material (as one of the channels of its ablative degradation). For this procedure, as the first stage, thermodynamic methods can be used to simulate the composition and properties of reactive C–H–O–N–Ar–Me-systems with variable set of such input parameters as the ratio of components of plasma-forming mixture, its pressure and temperature. We theoretically estimated the evaporative degradation of the material for three variants of EAPT cathode with alkane-containing plasmas (“hot” thermochemical zirconium and thermionic tungsten, and “cold” copper) in equilibrium and quasi-equilibrium modes of “plasma gas + surface cathode material”-mixture, with use of generalized thermodynamic properties of the materials. The calculation for conditions with pressure, which is characteristic for EAPT discharge chamber, showed that when varying the initial composition of the plasma-forming mixture (from oxidizers (air or combustion products of alkanes) to reducing gases based on the products of combined partial oxidation and pyrolysis of alkanes), the effect of a difference in the cathode evaporation rate EAI was observed in systems based on (air + alkane)-mixtures near the melting point of surface cathode substances, in a comparison with the case of EAPTs with more conventional gases (commercial N 2 , air) and, importantly, for two variants of the analyzed cathodes (with the exception of copper). In addition, the electrode erosion value was compared for simulated zirconium cathode (in terms of erosion evaporative component) when operating on the combustion products of alkanes from “air + CH 4 ”-mixture, and for some known EAPTs with similar cathodes in other gases. Using the case of earlier tested DC plasma torch with rod Zr-cathode (with microheterogeneous surface) as an example, it was found that our calculation indicates non-monotonic dynamics of EAI value and fractions of Zr-containing vapors as a result of the change of the fuel-air equivalence ratio f of initial reactive mixture. This effect is inconsistent with measured cathode composition, which shows a probability of nonequilibrium character of thermal and diffusion processes in near-electrode plasma and surface layer (~1 mm) of the electrode, at least in the modes with arc current in the torch near 300 A. Besides this, it should be noted that obtained modeling data on the behavior of zirconium compounds (ZrO 2 , ZrC) in C–H–O–N–Ar–Zr-system can be used not only for improvement of the torch cathodes, but also for design of new Zr-containing thermal protection systems to predict preliminary their ablation rate in a flow of products of combustion (including incomplete one) of engine-, rocket- and other fuels. Similarly, the results on the copper compounds behavior near the metal evaporation temperature can be useful for optimizing the process of plasma spraying of copper alloy coatings.

Experimental Investigation of Electrode Erosion of Trigatron in Microsecond Arc Discharge Process

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Electrode erosion properties of gas spark switches for fast linear transformer drivers

Analysis of internal material characteristics of cathode crater of micro-cathodic arc thruster

Spectroscopic diagnosis and simulation analysis of tungsten cathode erosion during the start-up process for a magnetoplasmadynamic thruster

Evolution rules for cathode erosion and corresponding arc behaviour in tungsten inert gas welding

Experimental study on the DC discharge characteristics of wire-to-cylinder electrode configuration at high temperature

Effect of the Microstructure of Electrode Materials on Arc Cathode Spot Dynamics

Two-Electrode Ion-Extraction System of a Radio-Frequency Ion Source: Numerical and Experimental Studies of Erosion of the Accelerating Electrode

Chromium, a Promising Cathode Candidate for Homogeneous Arc Erosion in Air

Endurance-test and theoretical prediction of a rare earth nanocathode for the applied field magnetoplasmadynamic thruster

The Influence of Different Parameter on Electrode Erosion During Opening Process

A Study of the Surface Structure of Electrodes during Discharge in an Electrolyte in a Magnetic Field

Experimental investigations on the influence of discharge current waveform on processing characteristics and surface integrity in electrical discharge machining

Experimental study on the life and performance of an improved DC arc plasma torch

Experimental Investigation on Trapped Electrons Oscillation Suppression for W-Band Gyro-TWT

Evaluation of Evaporative Degradation of Arc Torch Cathodes in Hydrocarbon-Containing Plasmas for Spraying, Thermal Protection Testing and Related Technologies

Material wear of the tool electrode and metal workpiece in electrochemical discharge machining

Numerical study on the effects of discharge parameters on vacuum arc plasma

Influence of Different Tool Electrode Materials on Electrochemical Discharge Machining Performances