Abstract:Design of non-transferred DC electric arc plasma torches (EAPTs) operated with plasma gases containing alkane hydrocarbons, as a promising type of heaters for a number of technologies (thermal spraying, surface hardening, testing of thermal protection systems, etc.), requires taking into account the evaporation rate of surface cathode material (as one of the channels of its ablative degradation). For this procedure, as the first stage, thermodynamic methods can be used to simulate the composition and properties of reactive C–H–O–N–Ar–Me-systems with variable set of such input parameters as the ratio of components of plasma-forming mixture, its pressure and temperature. We theoretically estimated the evaporative degradation of the material for three variants of EAPT cathode with alkane-containing plasmas (“hot” thermochemical zirconium and thermionic tungsten, and “cold” copper) in equilibrium and quasi-equilibrium modes of “plasma gas + surface cathode material”-mixture, with use of generalized thermodynamic properties of the materials. The calculation for conditions with pressure, which is characteristic for EAPT discharge chamber, showed that when varying the initial composition of the plasma-forming mixture (from oxidizers (air or combustion products of alkanes) to reducing gases based on the products of combined partial oxidation and pyrolysis of alkanes), the effect of a difference in the cathode evaporation rate EAI was observed in systems based on (air + alkane)-mixtures near the melting point of surface cathode substances, in a comparison with the case of EAPTs with more conventional gases (commercial N 2 , air) and, importantly, for two variants of the analyzed cathodes (with the exception of copper). In addition, the electrode erosion value was compared for simulated zirconium cathode (in terms of erosion evaporative component) when operating on the combustion products of alkanes from “air + CH 4 ”-mixture, and for some known EAPTs with similar cathodes in other gases. Using the case of earlier tested DC plasma torch with rod Zr-cathode (with microheterogeneous surface) as an example, it was found that our calculation indicates non-monotonic dynamics of EAI value and fractions of Zr-containing vapors as a result of the change of the fuel-air equivalence ratio f of initial reactive mixture. This effect is inconsistent with measured cathode composition, which shows a probability of nonequilibrium character of thermal and diffusion processes in near-electrode plasma and surface layer (~1 mm) of the electrode, at least in the modes with arc current in the torch near 300 A. Besides this, it should be noted that obtained modeling data on the behavior of zirconium compounds (ZrO 2 , ZrC) in C–H–O–N–Ar–Zr-system can be used not only for improvement of the torch cathodes, but also for design of new Zr-containing thermal protection systems to predict preliminary their ablation rate in a flow of products of combustion (including incomplete one) of engine-, rocket- and other fuels. Similarly, the results on the copper compounds behavior near the metal evaporation temperature can be useful for optimizing the process of plasma spraying of copper alloy coatings.

Chromium, a Promising Cathode Candidate for Homogeneous Arc Erosion in Air

Homogeneous Arc Ablation Behaviors of CuCr Cathodes Improved by Chromic Oxide

Inhomogeneous Ablation Behaviors and Failure Mechanism of Copper Cathode in Air

Copper Cathode’s Ablated Structure Operated in a 50 Megawatt Arc Heater

Sustainable and homogeneous arc ablation behavior of zirconium cathodes improved by in situ formation of zirconium oxides

Investigation of vacuum arc ignition characteristics and erosion morphology microstructure characteristics of CuCr55 electrode contact materials

Exploration of a Micro Multi-Electrode Technology Applied in an Air Arc Heater

Arc Erosion Resistance of CuCrMo Films Deposited Via Magnetron Sputtering

Laser Cladding of Layered Zr/Cu Composite Cathode with Excellent Arc Discharge Homogeneity

Erosion behaviour of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres

Corrosion Behaviour of Nanochromium Coatings Deposited by Direct Current Magnetron Sputtering

Insights into surface modification and erosion of multi-element arc cathodes using a novel multilayer cathode design

Enhanced arc erosion resistance via constructing W particle network structure in cold sprayed CuCrZr–W coating: Implication for electromagnetic launching system

Layer-by-layer Laser Cladding of Crack-Free Zr/Nb/Cu Composite Cathode with Excellent Arc Discharge Homogeneity

Research on the influence of grain size of CuCr contact on the characteristics of cathode spot and cathode surface erosion in vacuum arc

Evaluation of Evaporative Degradation of Arc Torch Cathodes in Hydrocarbon-Containing Plasmas for Spraying, Thermal Protection Testing and Related Technologies

High-temperature erosion behavior of high-velocity arc-spraying FeMnCr/Cr3C2 coatings

Microstructure and Erosion Wear Characterization of a New Cast High-Vanadium–Chromium Alloy (HVCA)

Endurance-test and theoretical prediction of a rare earth nanocathode for the applied field magnetoplasmadynamic thruster

Effects of Heat Treatment and Erosion Particle Size on Erosion Resistance of a Hypereutectic High-Chromium Cast Iron

Chromium arc plasma characterization, structure and properties of CrN coatings prepared by vacuum arc evaporation