Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

Rapid Fabrication of Microhole Array Structured Optical Fibers

Compact Microfiber Bragg Gratings with High-Index Contrast

A Simple Approach to Fiber-Based Tunable Microcavity with High Coupling Efficiency

Fabrication of Optical Cavities with Femtosecond Laser Pulses

Microfluidic Refractive-Index Sensors Based On Small-Hole Microstructured Optical Fiber Bragg Gratings

Miniature Fabry-Perot Cavity Based on Fiber Bragg Gratings Fabricated by Fs Laser Micromachining Technique

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Photonic crystal formation on optical nanofibers using femtosecond laser ablation technique

Fabrication Of Functional Microstructured Optical Fibers Through A Selective-Filling Technique

Optical Fiber Mach-Zehnder Interferometer Based on a Pair of Microholes

High-Efficiency Inscription of Fiber Bragg Grating Array with High-Energy Nanosecond-Pulsed Laser Talbot Interferometer

Rapid Fabrication of Yttrium Aluminum Garnet Microhole Array Based on Femtosecond Bessel Beam

Micromachining & FBG fabrication using point by point technique utilizing femto-second laser

An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser

Optimized femtosecond laser direct-written fiber Bragg gratings with high reflectivity and low loss

A Microfiber Bragg Grating Based On A Microstructured Rod

Review of Femtosecond-Laser-Inscribed Fiber Bragg Gratings: Fabrication Technologies and Sensing Applications

Realization of All-in-Fiber Liquid-Core Microstructured Optical Fiber

Silt-Beam Shaping Method for Femtosecond Laser Point-by-Point Inscription of Highly Localized Fiber Bragg Gratings with Enhanced Cladding Modes

Microchanneled Chirped Fiber Bragg Grating Formed by Femtosecond Laser-Aided Chemical Etching for Refractive Index and Temperature Measurements

Design guidelines and characteristics of beam-shaping microstructure optical fibers