Abstract:Abstract This paper presents 3D Fabry–Pérot (FP) cavities fabricated directly onto cleaved ends of low-loss optical fibers by a two-photon polymerization (2PP) process. This fabrication technique is quick, simple, and inexpensive compared to planar microfabrication processes, which enables rapid prototyping and the ability to adapt to new requirements. These devices also utilize true 3D design freedom, facilitating the realization of microscale optical elements with challenging geometries. Three different device types were fabricated and evaluated: an unreleased single-cavity device, a released dual-cavity device, and a released hemispherical mirror dual-cavity device. Each iteration improved the quality of the FP cavity’s reflection spectrum. The unreleased device demonstrated an extinction ratio around 1.90, the released device achieved 61, and the hemispherical device achieved 253, providing a strong signal to observe changes in the free spectral range of the device’s reflection response. The reflectance of the photopolymer was also estimated to be between 0.2 and 0.3 over the spectrum of interest. The dual-cavity devices include both an open cavity, which can interact with an interstitial medium, and a second solid cavity, which provides a static reference reflection. The hemispherical dual-cavity device further improves the quality of the reflection signal with a more consistent resonance, and reduced sensitivity to misalignment. These advanced features, which are very challenging to realize with traditional planar microfabrication techniques, are fabricated in a single patterning step. The usability of these FP cavities as thermal radiation sensors with excellent linear response and sensitivity over a broad range of temperature is reported. The 3D structuring capability the 2PP process has enabled the creation of a suspended FP heat sensor that exhibited linear response over the temperature range of 20 oC –120 oC; temperature sensitivity of ∼50 pm oC −1 at around 1550 nm wavelength; and sensitivity improvement of better than 9x of the solidly-mounted sensors.

An Efficient Non-Invasive Method to Fabricate In-Fiber Microcavities Using a Continuous-Wave Laser

Fabrication of Optical Cavities with Femtosecond Laser Pulses

High-Q, Low-Mode-volume Microsphere-Integrated Fabry–Perot Cavity for Optofluidic Lasing Applications

Recent Progress in Optical Micro/Nanofiber Technology

A Simple Approach to Fiber-Based Tunable Microcavity with High Coupling Efficiency

Fabrication of high-Q microresonators in dielectric materials using a femtosecond laser: Principle and applications

Femtosecond Laser Direct Writing of High-Q Microresonators in Glass and Crystals

Toward On-Chip Unidirectional and Single-Mode Polymer Microlaser

An On-Line Fiber Cutting-Welding Method for the Fabrication of Fabry-Perot Micro-Cavity

Arc Discharge Method to Fabricate Large Concave Structures for Open-Access Fiber Fabry-Pérot Cavities

Novel Method of Fabricating Fabry-Perot Cavity Employing MEMS Wet-Etching Process

Fabrication and Analysis of a Fabry-Perot Cavity with a Micromechanical Wet-Etching Process.

Three-dimensional Fabry–Pérot cavities sculpted on fiber tips using a multiphoton polymerization process

Facile microfluidic fabrication of monodispersed self-coupling microcavity with fine tunability

Femtosecond Laser One-Step Microfabrication Of Optical Fiber Inline Square Resonators For Chemical Sensing

High‐Q Polymer Microcavities Integrated on a Multicore Fiber Facet for Vapor Sensing

Femtosecond laser 3D fabrication of whispering-gallery-mode microcavities

Robust Packaged Fiber-Microcavity Device with over One Billion Q-factor

Fabrication of a centimeter-long cavity on a nanofiber for cavity QED

Micro-cavity fabricated by femtosecond lasers and its application in fiber-loop ring-down spectroscopy

Novel laser machining of optical fibers for long cavities with low birefringence