Abstract:Polymer electrolyte membrane fuel cells (PEMFCs) are one of the most promising energy devices for both mobile and stationary applications due to their high energy conversion efficiency and low environment pollution. However, there are some problems to be solved. PEMFCs operating at low temperatures (below 80℃) based on Nafion require humidification and have low CO tolerance. To overcome this problem, high-temperature PEMFCs that operate up to 180℃ are being studied. High temperature PEMFCs does not require humidification, which simplifies the system and is highly resistant to CO. It also has the advantage of using waste heat. However, the cell performance of high-temperature PEMFCs is still much lower than that of low-temperature PEMFCs and needs to be increased for practical applications The reason for this is slow Oxygen Reduction Reaction (ORR) and limited transport of protons and reactants, especially in the presence of phosphoric acid in the catalyst layer. In the high-temperature PEMFCs, phosphoric acid acts as a proton conduction as an electrolyte and is a necessary element for electrochemical reactions at the triple phase boundaries. Therefore, if the amount of phosphoric acid in the catalyst layer is too small, it exhibits low electrochemical activity. If it is too much, the pore inside the catalyst layer is blocked to restrict the movement of the fuel, thereby reducing the number of triple phase boundaries and reducing the performance. Therefore, the amount and distribution of phosphoric acid and the formation of structural network pores in the catalyst layer are important. Thus, several polymeric binders have been introduced to perform this role. Among them, PTFE is known as the most promising binder. PTFE has hydrophobicity and high chemical stability. However, PTFE easily agglomerates and sinks immediately in the solvent due to its high hydrophobicity. Therefore, if an electrode is made of a catalyst slurry that does not properly disperse PTFE, uniform PTFE distribution in the catalyst layer cannot be expected. So, in the catalyst layer, there may be more or less parts of the specific part than the desired PTFE content. Therefore, it is not only difficult to form a proper phosphoric acid distribution and structural network of the catalyst layer, but also may affect the reproducibility of electrode manufacturing. In this study, the catalytic electrode was prepared by introducing a surfactant to disperse PTFE in the preparation of catalyst slurry. Single cell test was carried out using membrane electrode assembly made from this electrode. And the electrochemical and structural characterizations were compared. The details will be discussed in presentation.

Plasma-Induced Styrene Grafting Onto The Surface Of Polytetrafluoroethylene Powder For Proton Exchange Membrane Application

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Modified sulfonated poly(phthalazinone ether ketone) membranes with inorganic particles for potential applications in PEMFCs

Study on the mechanism of graft polymerization and sulfonation of proton exchange membranes for fuel cell

Quantitative analysis of proton exchange membrane prepared by radiation-induced grafting on ultra-thin FEP film

Expanded polytetrafluoroethylene functionalized with free radical scavengers and hydrophilic groups for superior chemical stability of proton exchange membranes

Fabrication of Silane-crosslinked Proton Exchange Membranes by Radiation and Evaluation of Fuel Cell Performance

Sulfonated Polyimide Membranes Grafted with Sulfoalkylated Side Chains for Proton Exchange Membrane Fuel Cell (PEMFC) Applications

Effect of Surfactant for PTFE Binder Dispersion of Electrodes Prepared by Bar Coating Method in High Temperature Polymer Electrolyte Membrane Fuel Cell

Preparation of a Novel Proton Exchange Membrane Using Radiation Grafted ETFE Film for Fuel Cell

Superhydrophobic Carbon Functionalized by Chemical Grafting of Fluoroalkylsilane Enables an Efficient Microporous Layer for Proton-Exchange Membrane Fuel Cells

Radiolytic Fabrication and Characterization of Ptfe-G-Paa As the Supporters for the Reinforced Composite Fuel Cell Membrane

Grafting free radical scavengers onto polyarylethersulfone backbones for superior chemical stability of high temperature polymer membrane electrolytes

Proton Exchange Membrane from Tetrazole-Based Poly (phthalazinone Ether Sulfone Ketone) for High-Temperature Fuel Cells

Plasma-grafted Anion-Exchange Membrane Preparation and Process Analysis

Development of Porous-PTFE Reinforced Proton Exchange Membranes

PVDF Based Ion Exchange Membrane Prepared by Radiation Grafting of Ethyl Styrenesulfonate and Sequent Hydrolysis

Fuel 109-New Proton Conductive Composite Materials with Inorganic and Styrene Grafted and Sulfonated Vdf/Ctfe Fluoropolymers

Radiation Grafting of Styrene and Maleic Anhydride Onto PTFE Membranes and Sequent Sulfonation for Applications of Vanadium Redox Battery

Fabrication of Support Tubular Proton Exchange Membrane For Fuel Cell

Surface features of polymer electrolyte membranes for fuel cell applications: An approach using S2p XPS analysis