Abstract:Abstract Al–Zn–Mg–Cu–Zr aluminum alloys have shown promise as materials for drill pipes; however, their application temperature is limited to below 120°C. This study investigates the influence of incorporating the rare earth element Nd on the microstructure and mechanical properties of Al–Zn–Mg–Cu–Zr alloys. The microstructural evolution during casting, homogenization, hot deformation, and heat treatment processes is characterized using optical microscopy and scanning electron microscopy. The composition of the rare earth phase is determined through transmission electron microscopy (TEM). Furthermore, first-principles calculations are employed to determine the formation enthalpy, cohesive energy, shear modulus, bulk modulus, Young’s modulus, and Poisson’s ratio of bulk Al 8 Cu 4 Nd. The effect of Nd addition on the mechanical properties of the alloy is investigated through hardness and tensile testing. The results indicate that the addition of Nd significantly refines the grain and dendrite sizes of the alloy and effectively suppresses recrystallization behavior during hot extrusion and solution treatment. TEM observations reveal the presence of micrometer-sized blocky Al 8 Cu 4 Nd phases and nanometer-sized Al 3 Nd phases. The Al 3 Nd phases are located near dislocations, hindering dislocation movement and thus enhancing the alloy’s mechanical properties. First-principles calculations demonstrate that the bulk Al 8 Cu 4 Nd phase exhibits superior structural stability, deformation resistance, and brittle characteristics, which negatively impact the ductility of the alloy. The alloy with Nd addition can maintain a high hardness value for an extended period at high temperature, and the tensile strength of the alloy with 0.26 wt% Nd addition reaches 396.2 MPa at 120°C. These results indicate that the rare earth element Nd can improve the high-temperature mechanical properties of the alloy.

Catalysis of Rare Earth Element Nd on Boriding of Aisi 1045 Steel

Effect of rare earth addition on diffusion kinetics of borided TC21-DT titanium alloy

Effect of rare earth (RE) on pack boronising process of titanium alloy

Effects of rare-earth elements on the oxidation behavior of γ-Ni in Ni-based single crystal superalloys: A first-principles study from a perspective of surface adsorption

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Acceleration of Plasma Nitriding at 550 °C with Rare Earth on the Surface of 38CrMoAl Steel

Kinetics of Formation, Metallurgical and Tribological Properties of Iron Boride Surface Layer on Steel ASTM A572

Effect of rare earth Nd on the microstructural transformation and mechanical properties of 7xxx series aluminum alloys

Promoting effect of Nd on the reduction of NO with NH3 over CeO2 supported by activated semi-coke: an in situ DRIFTS study

Heterogeneous nucleation of carbides attached to Y2O3 in Y-modified H13 steel

Effect of Nb Addition on Oxidation Mechanisms of High Cr Ferritic Steel in Ar–H2–H2O

Catalytic gas nitriding of M50NiL steel by LaFeO 3 pervoskite oxide under low-pressure conditions

Synthesis and Characterization of Nanocrystalline Boron-Nitride Thin Films by Ion Milling and Thermal Treatment for Tribological Coatings: An Approach to Quantifying the Growth Dynamic Process

A novel rare earth-salt bath nitriding of TC21-DT titanium alloy

Effect of rare earth elements on microstructure and mechanical properties of bainite/martensite bearing steel

Effect of rare earth on primary carbides in H13 die steel and their addition method: a review

The influence of rare earth elements (Y, sc) on the interfacial binding properties between the precipitation phases Fe 2 B, FeB and the matrix Fe in boron steel

Effect of carbon and nitrogen diffusion zone on growth mechanism of boride layer produced on Q235 Steel

Dispersed CeO2 Nanorods with Low-Speed Mixing for Mechanical Properties Promotion of PTA Steel Coatings

Effect of Nd element on the microstructure and mechanical performance of brazed diamonds with Ni–Cr filler metal

Influence mechanism of rare earth (RE) on inclusion modification in non-oriented silicon steel