Abstract:Static and dynamic mechanical properties of cement-asphalt composites with various contents of asphalt incorporated were studied. Uniaxial compressive stress-strain curves of different cement-asphalt mortars (CAMs) with cement mass ratio (A/C) in the range of 0.2 to 1.0 were obtained by the Materials Testing System (MTS) under different testing temperatures ranging from -40 to 80 degrees C. Two typical CAMs, one with A/C of 0.2 denoted by LAC and the other with A/C of 0.9 denoted by HAC, were chosen to be tested at varied deformation rates over a range of 0.3 to 30 mm/min at room temperature. The correlation between mechanical properties, e.g., peak stress or elastic modulus, and temperature or loading rate was, respectively, acquired. As a result, temperature sensitivity and loading rate dependence for mechanical behavior of different CAMs were analyzed. Dynamic mechanical analysis (DMA) on three cement-asphalt binders (CABs) with A/Cs from 0.2 to 1.0 was carried out, and temperature spectra and frequency spectra were obtained. The Burger model was used to simulate the viscoelastic mechanical behaviors of CABs. Results indicate that peak stress and elastic modulus of CAMs decline with the increasing A/C and temperature. The temperature sensitivity and the loading rate dependence for mechanical properties of CAMs with higher A/Cs are greater than those of CAMs with lower A/Cs. To quantify the dependence of mechanical properties on temperature and loading rate, temperature-sensitive factor and rate-influencing factor are defined separately. The two factors increase with the A/C, implying that CAMs with higher A/Cs have greater dependence on temperature and loading rate. Furthermore, the two factors for peak stress are bigger than those for elastic modulus for a given CAM. Dynamic modulus of CABs descends with the increase of A/C or temperature but ascends with the loading frequency. As the temperature rises or A/C increases, the viscoelasticity becomes more remarkable. The dependence of dynamic modulus of CABs with varied A/Cs on loading frequency is successfully simulated by using the Burger model.

INVESTIGATION ON DYNAMICAL MECHANICAL BEHAVIORS OF CEMENT-ASPHALT BINDERS

Static and Dynamic Mechanical Properties of Cement-Asphalt Composites

Time-temperature-aging-depth Shift Functions for Dynamic Modulus Master Curves of Asphalt Mixtures

Static and dynamic mechanical behavior of cement asphalt mortars

Study of the Viscoelasticity for Fibrous High ViscoelasticAsphalt Sand

Research on High- and Low-Temperature Rheological Properties of High-Viscosity Modified Asphalt Binder

Nonlinear Viscoelasticity and Viscoplasticity Characteristics of Virgin and Modified Asphalt Binders

Investigation of Viscoelastic Properties of Polymer-Modified Asphalt at Low Temperature Based on Gray Relational Analysis

Nonlinear Viscoelastoplastic Kinetics for High-Temperature Performance of Modified Asphalt Binders

Micromechanics Modeling of Viscoelastic Asphalt-Filler Composite System with and Without Fatigue Cracks

Cement Asphalt Mastic Dynamic Mechanical Properties and Microstructure Research

Study on Viscoelastic Properties of Various Fiber-Reinforced Asphalt Binders

The effects of aging on the viscoelastic properties of cement asphalt composite mastic

Effects of Freeze-Thaw on Dynamic Mechanical Behavior of Cement Emulsified Asphalt Composite Binder

Analysis of Linear Viscoelastic Response Function Model for Asphalt Binders

Dynamic Viscoelastic Property of Hard-Grade Asphalt Mixture

Research on high- and low-temperature properties of asphalt-mineral filler mastic

Investigation of Dynamic Viscoelastic Characteristics of Permeable Asphalt

Nonlinear Constitutive Model of High-Temperature Viscoelastic Deformation of Gussasphalt Concrete

Study on Dynamic Modulus of Asphalt Mixture in Cold Regionunder Rotary Accelerated Loading

Conversion from Shear Creep Compliance to Relaxation Modulus of Asphalt Binder Using Cauchy Residue Method and Experimental Validation