Abstract:Journal of Composite Materials, Ahead of Print. Carbon fiber-reinforced composites have become increasingly favored in the aerospace and automotive sectors for their remarkable performance attributes. Nonetheless, their broader adoption is hindered by the concern of delamination. To address this limitation, our study delved into the influence of incorporating a thermoplastic toughening agent on the interlaminar fracture toughness (ILFT) of woven carbon fiber composites. Our investigation focused on the impact of diverse curing pressures on these composites, analyzing configurations both with and without an integrated non-woven polyamide (PA) veil. The PA veil was meticulously positioned within the central layer of a composite, combining benzoxazine and carbon fiber constituents. Our primary objective entailed optimizing curing conditions to enhance ILFT across both Mode-I and Mode-II fracture modes. Our findings unveiled that elevating curing pressure had a limited effect on ILFT in non-interleaved composites while interleaved samples exhibited substantial ILFT reductions under heightened curing pressure. Raising pressure from 1 atm to 3.5 atm caused approximately a 27% drop in the Mode-I strain energy release rate (GIC) value, and this reduction deepened to 42% at 7 atm. This highlighted the inverse relationship between increased curing pressure and GIC values in interleaved specimens, while non-interleaved counterparts experienced less pronounced changes. A parallel trend manifested in Mode-II ILFT, where escalated curing pressure correlated with diminished Mode-II strain energy release rate (GIIC) values. Interleaved samples suffered a notably more significant decline, attributed to resin content reduction caused by heightened pressure. This, in turn, compromised the bond between the PA veil and the matrix, facilitating the propagation of cracks within the composite. This ultimately culminated in significantly reduced GIC and GIIC values. Our study contributes valuable insights into optimizing the interlaminar fracture toughness of carbon fiber composites, shedding light on the complex interplay of curing conditions and material configurations.

Influence of Carbon Fiber Pre-Treatments on Interlaminar Shear Strength and Fracture Behavior of C/C Composites

Effect of CNT film interleaves on the flexural properties and strength after impact of CFRP composites

Exploring the influence of specimen types on the intralaminar fracture behavior of fiber-reinforced polymer matrix composites

Increasing the interlaminar fracture toughness and thermal conductivity of carbon fiber/epoxy composites interleaved with carbon nanotube/polyimide composite films

Effects of preform structure on microstructure and mechanical properties of long/short fiber‐coupled C/C–SiC composites

Effect of Surface Treatment of Carbon Fiber on the Mechanical Properties of C-f/SiO2 Composite

Interlaminar toughening in structural carbon fiber/epoxy composites interleaved with carbon nanotube veils

Influence of Sintering Process on the Fracture Behavior of C-F/SiC Laminated Ceramic Composites

Enhanced Electrical Conductivity and Interlaminar Fracture Toughness of CF/EP Composites via Interleaving Conductive Thermoplastic Films

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Interfacial properties of carbon fiber‐reinforced biobased resin composites by single fiber fragmentation, fiber push‐out, and interlaminar shear strength

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites

Investigation of interlayer toughening of carbon fiber composites using non-woven polyamide veils under different curing pressures

Effect of fiber surface treatment with silane coupling agents and carbon nanotubes on mechanical properties of carbon fiber reinforced polyamide 6 composites

Understanding interlaminar toughening of unidirectional CFRP laminates with carbon nanotube veils

Effect of carbon nanotubes grown temperature on the fracture behavior of carbon fiber reinforced magnesium matrix composites: Interlaminar shear strength and tensile strength

Interlaminar fracture toughness of carbon/epoxy composites laminates toughened by short carbon fiber

Improving Interlaminar Fracture Toughness and Impact Performance of Carbon Fiber/Epoxy Laminated Composite by Using Thermoplastic Fibers

Free-Standing CNT Film for Interlaminar Toughening: Insight into Infiltration and Thickness Effects

A multiscale study of heat treatment effects on the interlayer mechanical properties of 3D printed continuous carbon fiber‐reinforced composites

A multi-layer resin film infusion process to control CNTs distribution and alignment for improving CFRP interlaminar fracture toughness