Abstract:Increasing the performance of an energetic material can be achieved by changing its composition or using additives, such as metal powders. Aluminum hydride (AlH3) exhibits attractive properties, such as high hydrogen/energy storage, relatively good stability, and low dehydrogenation temperature. AlH3 has excellent prospects for use as a component in solid propellants for increasing the specific impulse of rocket engines and effectively reducing the erosion of engine nozzles. In this work, the effect of AlH3 on the energy performance, ignition characteristics, and combustion characteristics of solid propellants, as well as the agglomeration characteristics of metal particles was investigated. It was found that with increasing AlH3 content, the theoretical mass heat of combustion and the theoretical volumetric heat of combustion of the propellants increased, and the combustion efficiency also gradually improved. When the content of AlH3 in the propellant increased from 0.00% to 17.00%, the temperature of the propellant combustion chamber was reduced from 3314.59 to 2957.49 K and the theoretical specific impulse increased from 2584.2 to 2641.7 N center dot s/kg. The average molecular mass of the gas was reduced from 25.54 to 21.54 due to the large amount of hydrogen gas released by the combustion of AlH3. The maximum combustion temperature decreased and the burning rate increased with the gradual replacement of aluminum (Al) in the propellant with AlH3. The maximum combustion temperatures of the pure Al propellant and the pure AlH3 propellant were 2510.5 and 2232.5 K, respectively. The linear burning rates were 0.29 and 0.46 cm/s at 1.0 MPa, respectively. The agglomeration process of AlH3 included three main stages, namely accumulation, aggregation, and agglomeration. With the increase in the AlH3 content, the number of agglomerated particles in the propellant gas-phase flame region decreased continuously. (c) 2023 Published by Elsevier Inc. on behalf of The Combustion Institute.

Basic Performance of Hydrogen Storage Alloy Combustion Agent

Preparation and Properties of Mg-based Hydrogen Storage Alloys for Hybrid Electric Vehicle

Electrochemical Properties and Structural Analysis of Non-Stoichiometric Hydrogen Storage Alloys

Phase Structures And Hydrogen Storage Capabilities Of The Alloys (Ml)(X) (Ni3.8co0.75mn0.4ti0.05)

Hydrogen Storage Properties of Ti-Cr-Mn-M (M=V, Fe, Ni, Cu) Alloys

Microstructures and Hydrogen Storage Properties of Ti10V83-xFe6ZrMnx Alloys

Synthesis and Stability of Hydrogen Storage Material Aluminum Hydride

Dehydrogenation Performances of Different Al Source Composite Systems of 2libh4 + M (M = Al, LiAlH4, Li3AlH6).

Hydrogen Storage Properties and Crystal Structure of Ti-Cr Based Alloys

Hydrogen storage performances, kinetics and microstructure of Ti<sub>1.02</sub>Cr<sub>1.0</sub>Fe<sub>0.7-x</sub>Mn<sub>0.3</sub>Al<su b>x</sub> alloy by Al substituting for Fe

Study on Cyclic Hydrogen Storage Properties of LaNi5-xAlx (x=0-1.2) Alloys

Enhanced stability and combustion performance of AlH3 in combination with commonly used oxidizers

Influence of element substitution on structural stability and hydrogen storage performance: A theoretical and experimental study on TiCr2-xMnx alloy

Electrochemical Properties and Rietveld Analysis of Gas Atomized AB5 Hydrogen Storage Alloys with Low Co Content

Insights into the structure–performance relationship in La–Y–Ni-based hydrogen storage alloys

CO Impurities Effect on LaNi4.7Al0.3 Hydrogen Storage Alloy Hydrogenation/dehydrogenation Properties

Effect of AlH 3 on the Energy Performance and Combustion Agglomeration Characteristics of Solid Propellants

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

Study on Microstructure and Hydrogen Storage Properties of Mg80Ni16−xAlxY4 (x = 2, 4, 8) Alloys

Thermal Oxidation and Heterogeneous Combustion of AlH3 and Al: A Comparative Study

Compositional Dependence of Hydrogenation Performance of Ti-Zr-Hf-Mo-Nb High-Entropy Alloys for Hydrogen/tritium Storage