Abstract:Dielectrophoresis works on the dipoles through entire dielectric liquid through a non-uniform electric field, reversibly changing the droplet contact angle, and overcoming the contact angle saturation limit of electrowetting to affect the surface wettability as a volume force. However, it is difficult to realize useful three-dimensional tunable optical devices because most of the driving electrodes need to be patterned. This paper proposes a model of double flexible electrodes simulating planar interdigitated pattern electrodes based on the dielectrophoresis. Double flexible electrodes wrapped with an insulation layer and disconnected, arranged at close intervals, and wound along the plane substrate to form a two-dimensional plane line wall. A hydrophobic layer is applied to fill the gap and increase the initial contact angle. Ultimately, the "dropletinterdigitated planar line wall" dielectrophoresis driven-droplet model is formed after the dielectric droplets are deposited on the line wall's surface. Firstly, considering the influence of penetration depth and electrode gap area, Young's equation is theoretically modified to adapt to this model. Then, the potential distribution of this model and the planar interdigitated pattern electrode model is compared and analyzed by finite element algorithm simulation. The field strength distribution of the electrode with different wire diameters and insulating layer thicknesses is analyzed. It can be found that with the increase of the diameter of the electrode wire and the thickness of the insulating layer, the morphology of the model changes from the tip electrode to the planar electrode, the surface field strength attenuates exponentially and the peak value decreases. This shows that the electrode structure in this model is superior to the planar electrode. After that, the contact angle of the model is measured experimentally in the range of[58°, 90°] under a 0-250 Vrms voltage, which is in line with the theoretical expectation. At the same time, no obvious contact angle lag or saturation were observed in the experiment. Finally, the new electrophoretic driving droplet model constructed in this paper transforms the dielectric electrophoretic driving mode from a twodimensional planar electrode to a one-dimensional flexible linear electrode. Because of its flexibility and plasticity, it is convenient to form a three-dimensional cavity and can be applied to more complex device structures.

Influence of Distorted Electric Field Distribution on Microstructure Formation in the Electrohydrodynamic Patterning Process

Numerical Study of the Faithful Replication of Micro/nanostructures on Curved Surfaces by the Electrohydrodynamic Instability Process.

Electrically Induced Nanostructuring over Large Area--a New Idea from Concept to Practice

Near thermal-electric field controlled electrohydrodynamic 3D printing of high aspect ratio microstructures

Numerical Model of Jet Formation During Melt Electrowriting for Fabrication of Precise Structures

A Novel Approach to Study Patterned Thin Film Local Stress for Microelectronics Application

Defects in Micro Hot Embossing Process

Self Assembly of Polymer Structures Induced by Electric Field

Surface Patterning of Soft Polymer Film-Coated Cylinders Via an Electric Field

Non-ultraviolet-based patterning of polymer structures by optically induced electrohydrodynamic instability

A Full-Scale Computational Study on the Electrodynamics of a Rigid Particle in an Optically Induced Dielectrophoresis Chip

Study on Polymer Flow Profile in Micro Hot Embossing

Rapid In‐Plane Pattern Growth for Large‐Area Inverse Replication Through Electrohydrodynamic Instability of Polymer Films

All-optical associative memory based on the use of the laser as a nonlinear element.

An Analysis of the Uneven Tool Electrode Wear Mechanism in the Micro-electrical Discharge Machining Process

A deeper insight into the influence of the electric field densities in Melt-Electrowriting: Printing in the 4th Dimension

Electro-mechanically guided growth and patterns

Two-photon polymerized wetting morphologies for tunable external and internal electrode micropatterning

Study on liquid dielectrophoresis based on double flexible electrodes simulating interdigitated pattern electrodes

Electrochemical Replication and Transfer for Low-Cost, Sub-100 Nm Patterning of Materials on Flexible Substrates.

Integration of Electrospray and Digital Light Processing for Freeform Patterning of Porous Microstructures