Abstract:This work successfully fabricated the fine-grained Mg-2.6Nd-0.55Zn-0.5Zr (wt%) alloy plates with the average grain sizes of 2.39–3.49 μm via the extrusion process. The microstructure evolution during extrusion process and the associated mechanical properties were investigated. Results showed that dynamic recrystallization (DRX) significantly refined the grain size and improved the microstructure homogeneity. Extrusion fragmentation effect on the coarse Mg12Nd particles contributed to the development of fine-grained uniform microstructure, especially at the lower extrusion temperature. Additionally, extrusion process turned the fiber basal texture into the double peak basal texture owing to the sequential deformation mode activation from basal slip and tension twinning to pyramidal <c+a> slip. Subsequent continuous DRX and particle-stimulated nucleation (PSN) recrystallization played a weakening effect on the double peak basal texture. Moreover, decreasing the extrusion temperature increased the activation difficulty of pyramidal <c+a> slip and weakened the effect of PSN on texture modification, leading the basal plane distribution along the extrusion direction to be strengthened. Fine-grained strengthening significantly improved the mechanical properties, but such strengthening capability was severely dependent on the texture. During tension deformation, the weak basal texture easily activated the basal slip whereas the strong basal texture needed to activate the prismatic slip. Hall-Petch analysis indicated that the higher yield stress in the strong basal texture was ascribed to the remarkable deformation mode strengthening (activation of prismatic slip) and the geometrical strengthening (higher Taylor factor). The weak basal texture was beneficial to improve the uniform elongation owing to the higher strain hardening ability, which was more obvious when the tension twinning was activated.

A Comparative Study of Texture and Ductility of Mg–1.2Zn–0.8Gd Alloy Fabricated by Rolling and Equal Channel Angular Extrusion

Influence of Texture and Grain Size on the Room-Temperature Ductility and Tensile Behavior in a Mg–Gd–Zn Alloy Processed by Rolling and Forging

Effects of Gd Concentration on Microstructure, Texture and Tensile Properties of Mg–Zn–Gd Alloys Subjected to Large Strain Hot Rolling

Microstructure, Mechanical Properties and Texture Evolution of Mg–Al–Zn–La–Gd–Y Magnesium Alloy by Hot Extrusion and Multi-Pass Rolling

Room-temperature Ductility and Anisotropy of Two Rolled Mg–Zn–Gd Alloys

Excellent Room-Temperature Ductility and Formability of Rolled Mg–Gd–Zn Alloy Sheets

Ductility enhancement in Mg–8.7Gd–4.18Y–0.42Zr magnesium alloy fabricated through extrusion and equal channel angular pressing (EX-ECAP)

Activation of {1 01¯2} Twinning and Slip in High Ductile Mg–2.0Zn–0.8Gd Rolled Sheet with Non-Basal Texture During Tensile Deformation at Room Temperature

Evading Strength-Ductility Tradeoff in Mg Alloy via Uniform Microstructure and Unique Texture Modification Induced by Moderate Temperature ECAP

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Formation Mechanism of <0001> Texture Connected with Excellent Ductility During Hot Extrusion in Mg-9Gd-5Y-0.5Zr Alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Texture role in the mechanical property improvement contributed by grain refinement for Mg-2.6Nd-0.55Zn-0.5Zr alloy subjected to extrusion process

Microstructure and Texture Evolution During Hot Rolling and Subsequent Annealing of Mg–1Gd Alloy

Study on the low mechanical anisotropy of extruded Mg-Zn-Mn-Ce-Ca alloy tube in the compression process

Effects of Extrusion Ratio on the Microstructure, Texture and Mechanical Properties of Mg-2.5Nd-0.5Zn-0.5Zr Alloy Sheets

Study of strength-ductility and anisotropic behavior of Mg-Gd-Y-Zn-Zr alloy prepared by Equal channel double angular pressing

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Microstructure evolution, texture and mechanical properties of a Mg–Gd–Y–Zn–Zr alloy fabricated by cyclic expansion extrusion with an asymmetrical extrusion cavity: The influence of passes and processing route

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling