Abstract:Ytterbium (Yb) containing magnesium alloys have aroused extensive interest due to their excellent mechanical properties after thermomechanical processing and heat treatment. Unfortunately, the sole effect of Yb addition on the microstructure and mechanical properties of pure Mg matrix remains uncertain to date. In this work, the effects of Yb concentration on the texture development and tensile properties of pure Mg matrix during hot extrusion and the subsequent annealing were systematically investigated. The results revealed that the constitutional supercooling induced by Yb addition refined the as-cast microstructure but exerted a negligible effect on the original columnar grain morphology. When extruded at 300 °C, the dynamic recrystallization (DRX) process was considerably retarded. The in-grain misorientation axes (IGMA) analysis combined with TEM observation indicated that non-basal slips operated with increasing Yb concentration. Specifically, the prismatic 〈a〉 slip should be robustly activated in Mg–1.0 Yb extrudate, promoting the formation of the texture with {10–10} plane normal to the extrusion direction (ED), while for the Mg–2.0 Yb counterpart, the increased activity of pyramidal 〈c + a〉 slip and the relaxation of basal/<c + a> dislocations generated an ED-tilted texture component. The preferential grain growth dominated the subsequent annealing texture development at 400 °C when a comparable grain size was achieved. An obvious ED-tilted texture intensity with the peak around 〈–12–13〉 was observed in Mg–2.0 Yb alloy, which was primarily caused by grains with the basal orientation vanished and with the non-basal orientations intensified due to a higher concentration of Yb solute. Favored by the grain refinement, the Mg–2.0 Yb extrudate exhibited a high tensile yield strength of 304 ± 3.5 MPa, while the subsequently annealed counterpart presented a favorable elongation to failure of 14.8 ± 1.2%, which mainly due to the homogeneous grain structure, weak ED-tilted texture, and dissolution of coarse phases after high-temperature annealing.

Formation Mechanism of <0001> Texture Connected with Excellent Ductility During Hot Extrusion in Mg-9Gd-5Y-0.5Zr Alloy

Analysis of Abnormal Texture Formation and Strengthening Mechanism in an Extruded Mg-Gd-Y-Zn-Zr Alloy

On the Origin of Non-Basal Texture in Extruded Mg-RE Alloys and Its Implication for Texture Engineering

Dynamic Recrystallization and Texture Evolution of Mg–Y–Zn Alloy During Hot Extrusion Process

Texture role in the mechanical property improvement contributed by grain refinement for Mg-2.6Nd-0.55Zn-0.5Zr alloy subjected to extrusion process

Texture, microstructure and mechanical properties of an extruded Mg-10Gd-1Zn-0.4Zr alloy: Role of microstructure prior to extrusion

Unveiling the Formation of Basal Texture Variations Based on Twinning and Dynamic Recrystallization in AZ31 Magnesium Alloy During Extrusion

Microstructure and Texture Evolution During Hot Rolling and Subsequent Annealing of Mg–1Gd Alloy

A Comparative Study of Texture and Ductility of Mg–1.2Zn–0.8Gd Alloy Fabricated by Rolling and Equal Channel Angular Extrusion

Evolution of Microstructures, Texture, Damping and Mechanical Properties of Hot Extruded Mg-Nd-Zn-Zr Alloy

The Influence of Developed Texture on the Mechanical Anisotropy and Deformation Modes of an As-Extruded Mg-Zn-Zr Alloy

Texture development and tensile properties of Mg–Yb binary alloys during hot extrusion and subsequent annealing

Microstructure and Texture Evolution with Sm Addition in Extruded Mg–Gd–Sm–Zr Alloy

Microstructure, Mechanical Properties and Texture Evolution of Mg–Al–Zn–La–Gd–Y Magnesium Alloy by Hot Extrusion and Multi-Pass Rolling

Thermal Stability of Different Texture Components in Extruded Mg–3Al–1Zn Alloy

Quasi-in-situ Observing the Rare Earth Texture Evolution in an Extruded Mg-Zn-Gd Alloy with Bimodal Microstructure

Tuning texture and precipitation using Y/Gd atomic ratio in iso-concentration Mg–Y–Gd–Ag–Zr extruded alloys

Effects of Extrusion Temperature on Texture Evolution in Mg-1Gd Alloy

Effect of Subgrain and the Associated DRX Behaviour on the Texture Modification of Mg-6.63Zn-0.56Zr Alloy During Hot Tensile Deformation

Grain Growth and Texture Evolution During Annealing in an Indirect-Extruded Mg–1Gd Alloy

Effects of Extrusion Ratio on the Microstructure, Texture and Mechanical Properties of Mg-2.5Nd-0.5Zn-0.5Zr Alloy Sheets

Formation Mechanism of &lt;0001&gt; Texture Connected with Excellent Ductility During Hot Extrusion in Mg-9Gd-5Y-0.5Zr Alloy