Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Selective Laser Melting (SLM) process is a powder-based metal Additive Manufacturing (AM) technique that can generate fully functional and geometrically complex shapes which can be used in actual load-bearing situations. The mechanical properties of SLM parts are highly dependent on process parameters. Generally, the as-built surface quality of SLM parts is not good enough, and finding the optimum values of the parameters to improve surface quality is an ongoing challenge. In this study, an experimental approach was taken to investigate the effect of process parameters and scanning strategy on the surface roughness of stainless steel 316L parts as well as determine the optimal values of parameters and optimum scanning strategy. Laser profilometry was applied to measure surface roughness. Results showed that the scanning speed was the most effective parameter; increasing it from 900 mm/s to 1200 mm/s caused 62.5% rougher surfaces. Also, increasing laser power from 255 W to 300 W resulted in 41.8% rougher surfaces. Smaller hatch spaces caused better surface quality; decreasing it from 0.1 mm to 0.04 mm improved surface quality by 16%. And lower scan pattern angles resulted in slightly rougher surfaces (by 2%). Changing the settings from minimum overlap to maximum overlap resulted in 73.6% better surface quality. It was found that insufficient melting is the main reason for poor surface quality. Surface quality was improved whenever the resultant effect of parameters caused sufficient melting conditions. The optimum values were found as 270 W laser power, 900 mm/s scanning speed, 0.06 mm hatch spacing and 75° scan pattern angle. The best surface quality was obtained for the chessboard scanning strategy, with scan vectors being parallel to each other in adjacent blocks and rotating by 90° in successive layers. The optimum strategy caused 2.5 times better surface quality than the strategy of the roughest sample.

Effects of the processing parameters on the forming quality of stainless steel parts by Selective Laser Melting

Study on the Technique During Selective Laser Melting of Stainless Steel Powder

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters

Simulation and experimental studies on process parameters, microstructure and mechanical properties of selective laser melting of stainless steel 316L

Study on the Effects of Powder Properties on the Performance of Stainless Steel Parts Produced by Selective Laser Melting

Effect of Process Parameters on Formability and Surface Quality of Selective Laser Melted Al-Zn-Sc-Zr Alloy from Single Track to Block Specimen

Study on the effects of the processing parameters on the single tracks and the block support structures fabricated by selective laser melting

Effect of Process Parameters on Surface Quality of Laser Selective Melting 316L Stainless Steel

Effect of Processing Parameters on the Densification of an Additively Manufactured 2024 Al Alloy

The effect of process parameters and scanning strategies on surface roughness of stainless steel 316L SLM parts

Effect of Processing Parameters on Forming Defects During Selective Laser Melting of AlSi10Mg Powder

Study on performance optimization of 316L stainless steel parts by High-Efficiency Selective Laser Melting

The Effect of Laser Power and Scanning Speed on Forming Structure in Selective Laser Melting Process

Microstructure of Selective Laser Melting Parts Under Different Scanning Strategies

Influence of Process Parameters of Forming Characteristics on Ti-6Al-4V Fabricated by Selective Laser Melting

Effect of scanning speed and laser power on formability, microstructure, and quality of 316L stainless steel prepared by selective laser melting

Numerical Simulation for the Effect of Scanning Speed and in Situ Laser Shock Peening on Molten Pool and Solidification Characteristics

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

The key metallurgical features of selective laser melting of stainless steel powder for building metallic part

Density Improvement of Metal Parts Directly Fabricated via Selective Laser Melting

Evaluation for Multiple Processing Parameters in Selective Laser Melting Based on an Integration of Mesoscale Simulation and Experiment Method