Abstract:Silica aerogels generally exhibit poor mechanical properties, which seriously restrict their commercial use and makes it necessary to reinforce their structures to obtain materials strong enough to withstand mechanical stresses. The incorporation of polymers into silica aerogels is a promising approach due to the enhancement in mechanical strength afforded and the possibility of imparting the hydrophobicity of the polymers to the resulting aerogels. However, the processes typically employed to prepare polymer-reinforced silica aerogels are complex, arduous and costly, requiring multiple washing and soaking steps for the infiltration of the polymer precursors after gelation and supercritical drying. Additionally, diffusion problems can result in heterogeneity in aerogel monoliths due to the use of various cross-linked polymers and the autoclave-limited dimensions of aerogels. In this study, a facile sol–gel route was developed to fabricate a large (500 cm3) polymer–silica aerogel monolith that was stable under atmospheric conditions and suitable for machining. The synthesis of the polymer–silica aerogels began with a facile one-pot reaction involving resorcinol (R), formaldehyde (F), methyltrimethoxysilane (MTMS), and N-(β-aminoethyl)-γ-aminopropyl-trimethoxysilane (AEAPTES), followed by an ambient-pressure drying process. The resulting aerogels were characterised by nitrogen adsorption–desorption, scanning electron microscopy (SEM), contact angle, and thermal conductivity measurements, and the aerogel mechanical properties were evaluated by a unidirectional compression test. The Young's modulus of compression of the aerogels was observed to increase from 3.95 to 34.88 MPa with an increase in the density of the aerogels from 0.14 to 0.26 g cm−3. Simultaneously, the aerogels were observed to be superhydrophobic, with a contact angle as high as 168°, and exhibited low thermal conductivity (0.038 W m−1 K−1) and good absorption for organic liquids, which are critical characteristics for the practical application of aerogels, especially in energy-saving and oil-/chemical-cleanup practices.

Ultralow Density, Hollow Silica Foams Produced Through Interfacial Reaction and Their Exceptional Properties for Environmental and Energy Applications

Ultralight Silica Foams with a Hierarchical Pore Structure Via a Surfactant-Free High Internal Phase Emulsion Process

Aerogel‐like Ceramic Foams with Super‐high Porosity and Nanoscale Cell Wall from Sol Nanoparticles Stabilized Foams

Silica Foams With Ultra-Large Specific Surface Area Structured By Hollow Mesoporous Silica Spheres

Eco-Friendly Fabrication of Highly Stable Silica Aerogel Microspheres with Core-Shell Structure

A Facile Green Chemistry Route to Porous Silica Foams

3D Printable Ultra‐Highly Porous and Mechanically Strong Foam Materials for Multiple Applications

Ultralight Alumina Ceramic Foams with Single-Grain Wall Using Sodium Dodecyl Sulfate As Long-Chain Surfactant

Highly Porous and Mechanically Robust Al2O3-based Foams with Self-Wrinkled and Rough Aperture Surfaces Via Binary Colloidal Self-Assembly of Nanoparticle/gelation Network

A Convenient and Versatile Strategy for the Functionalization of Silica Foams Using High Internal Phase Emulsion Templates As Microreactors.

Facile Synthesis of Surface-Modified Hollow-Silica (SiO2) Aerogel Particles via Oil–Water–Oil Double Emulsion Method

Ambient-pressure drying synthesis of large resorcinol–formaldehyde-reinforced silica aerogels with enhanced mechanical strength and superhydrophobicity

Ultralight and Flexible Monolithic Polymer Aerogel with Extraordinary Thermal Insulation by A Facile Ambient Process

Melt polymerization synthesis of a class of robust self-shaped olefin-linked COF foams as high-efficiency separators

Ultrahigh-strength silicone aerogels reinforced by an armor-like epoxy framework via a temperature-controlled sequential reaction strategy

Transparent, robust, and machinable hybrid silica aerogel with a “rigid-flexible” combined structure for thermal insulation, oil/water separation, and self-cleaning

Preparation of superhydrophobic and flexible polysiloxane aerogel

Ceramic foams with highly open channel structure from direct foaming method in combination with hollow spheres as pore-former.

Porous Silica Ceramics with Uniform Pores from the In-Situ Foaming Process of Silica Poly-Hollow Microspheres in Inert Atmosphere

Synthesis of ultrahigh-pore-volume carbon aerogels through a “reinforced-concrete” modified sol–gel process

Facile synthesis of mechanically flexible and super-hydrophobic silicone aerogels with tunable pore structure for efficient oil-water separation