Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Effect of compounding sequence on the morphology of organoclay-filled PA6/PP/MAPP blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Effects of Calcium Carbonate and Compounding Sequence on the Phase Morphology and Properties of Maleic Anhydride-Grafted Polypropylene Compatibilized Polyamide 6/polypropylene Blend

Combination of double-modified clay and polypropylene-graft-maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Effects Of Talcum Powder(Talc) And Compounding Sequence On The Morphology And Mechanical Properties Of Pa6/Pp/Mapp Blend

Cocontinuous Phase Morphology for an Asymmetric Composition of Polypropylene/polyamide 6 Blend by Melt Mixing of Polypropylene with Premelted Polyamide 6/organoclay Masterbatch

Tailoring the Morphology of Polypropylene/Polyamide 66 Blend at an Asymmetric Composition by Using Organoclay and Maleic Anhydride Grafted Polypropylene

The Influence of Calcium Carbonate on the Mechanical Properties and Phase Morphology of PA6/PP Blend

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Influence of Maleic Anhydride Grafted Polypropylene on the Dispersion of Clay in Polypropylene/Clay Nanocomposites

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

TOUGHENING OF ETHYLENE-PROPYLENE RANDOM COPOLYMER/CLAY NANOCOMPOSITES： COMPARISON OF DIFFERENT COMPATIBILIZERS

Morphology, thermal behavior, and mechanical properties of nylon6/multi-monomer grafted polypropylene blends

Rheological Study on High-Density Polyethylene/organoclay Composites