Abstract:Cu2S, consisting of Earth-abundant and eco-friendly elements, is a promising candidate for thermoelectric energy conversion. The stoichiometric Cu2S has intrinsically low thermal conductivity together with meagre electrical conductivity. Herein, in order to improve the electrical properties, we develop a facile solvothermal method for synthesizing a series of Cu2–xS with tunable phase compositions. With reduction in the CuCl/Na2S molar ratio in the solution precursors from 2:1 to 1.75:1, the solvothermal products transform from single-phase Cu2S into Cu2S–Cu1.96S composites, which are preserved in the hot-pressed pellets. The decreased CuCl/Na2S molar ratio results in increased room-temperature Hall carrier concentration, leading to enhanced electrical conductivity. Specifically, the pellet corresponding to the 1.75:1 CuCl/Na2S precursor ratio obtains a power factor of 8.04 μW cm–1 K–2 at 815 K, which is ∼735% of the value obtained by stoichiometric Cu2S. Along with the moderate thermal conductivity, this sample achieves an enhanced zT value of 0.87 at 815 K, representing a ∼250% increase when compared to stoichiometric Cu2S. This study demonstrates an effective strategy in enhancing the thermoelectric performance of solution-synthesized Cu2S-based materials by phase tuning.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c13050.Extra XRD, SEM, TEM, EPMA, EDS, and WDS results on the synthesized samples, calculated weight fraction of Cu1.96S in the samples, Rietveld refinement results, thermoelectric property comparison, and zT values of the Cu2S–Cu1.96S-3 pellets in the first three cycles (PDF)This article has not yet been cited by other publications.

Synthesis and transport property of Cu1.8S as a promising thermoelectric compound

Facile Synthesis of Monodisperse Cu3SbSe4 Nanoparticles and Thermoelectric Performance of Cu3SbSe4 Nanoparticle-Based Materials

Good Thermoelectric Performance and Stability in Copper Sulfide Synthesized by Hydrothermal Method and Densified by HP Technique

Chemical Precipitation Synthesis and Thermoelectric Properties of Copper Sulfide

High thermoelectric performance realized in porous Cu1.8S based composites by Na2S addition

Enhancing thermoelectric performance of Cu1.8S by Sb/Sn co-doping and incorporating multiscale defects to scatter heat-carrying phonons

Multiscale architectures boosting thermoelectric performance of copper sulfide compound

High Thermoelectric Performance Balanced by Electrical and Thermal Transport in Tetrahedrites Cu12+xSb4S12Se

Chemical Bonding Engineering for High-Symmetry Cu2S-based Materials with High Thermoelectric Performance

Thermoelectric Performance of Hydrothermally Synthesized Micro/nano Cu2-xS

Enhanced thermoelectric properties of Cu1.8S via the introduction of ZnS nanostructures

Synthesis-temperature-dependent Phase Composition Manipulation Toward High Thermoelectric Performance in Tetrahedrites

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Thermoelectric Properties of Non-Stoichiometric Cu2+xSn1-xS3 Compounds

Enhanced thermoelectric properties of bismuth sulfide polycrystals prepared by mechanical alloying and spark plasma sintering

Enhanced Thermoelectric Performance of Hydrothermal Synthesized Ag Incorporated Cu &Lt;sub>2-X</sub>s Micro/Nano Composites

Effects of sintering temperature on thermoelectric properties of Cu1.8S bulk materials

Electronic Transport and Thermoelectric Properties of Cu12-xZnxSb4S13 Tetrahedrites Prepared by Mechanical Alloying and Hot Pressing

Phase Tuning for Enhancing the Thermoelectric Performance of Solution-Synthesized Cu 2– x S

High Thermoelectric Performance in Cu2SnS3 by Control Over Phase‐Dependent Mobility Edge

Approaching high thermoelectric performance in p-type Cu3SbS4-based materials by rational electronic and nano/microstructural engineering