Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Mechanical Properties of Hot-dip Galvanized Dual Phase Steel DP590 and Its Constitutive Model

Change Characteristics of Static Mechanical Property Parameters and Dislocation Structures of 45(#) Medium Carbon Structural Steel During Fatigue Failure Process

Dynamic deformation behavior and corresponding constitutive model of ultra-high strength DP1000 steel

Research on dynamic deformation behavior and constitutive relationship of hot forming high strength steel

The Study and Application on Ductile Fracture Criterion of Dual Phase Steels During Forming

Mechanical Properties and Constitutive Models of Low Yield Point Steels

Effect of Material Anisotropy on the Mechanical Response of Automotive Steel under High Strain Rates

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Investigation of evolving yield surfaces of dual-phase steels

Mechanical properties and microstructure of the heterogeneous DZ2 axle steel under high-strain-rate compression at ambient temperature

Tensile Mechanical Behaviour of Ultra-High Strength Cold Rolled Dual Phase Steel DP1000 at High Strain Rates

Fracture of dual phase steel sheets under uniaxial tension (I): experimental study with dic techniques

Constitutive Model for Full-Range Cyclic Behavior of High Strength Steels Without Yield Plateau

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

High-Temperature Deformation Characteristics and Constitutive Model of an Ultrahigh Strength Steel

Analysis of the delayed cracking mechanism of an industrial hot-dip galvanized DP1180GI steel coil

Constitutive model for cyclic behavior of mild steel under various strain amplitudes

Constitutive modeling and analysis on high-temperature flow behavior of 25 steel

A three-dimensional constitutive model of High Strength Structural steels

A new constitutive model for high strength structural steels

Constitutive Model for Full-Range Elasto-Plastic Behavior of Structural Steels with Yield Plateau: Formulation and Implementation