Abstract:Hypothesis: Zirconia microparticles produced by sol-gel synthesis have great potential for photonic applications. To this end, identifying synthetic methods that yield reproducible control over size uniformity is important. Phase transformations during thermal cycling can disintegrate the particles. Therefore, understanding the parameters driving these transformations is essential for enabling high-temperature applications. Particle morphology is expected to influence particle processability and stability. Yttria-doping should improve the thermal stability of the particles, as it does in bulk zirconia. Experiments: Zirconia and YSZ particles were synthesized by improved sol-gel approaches using fatty acid stabilizers. The particles were heated to 1500 °C, and structural and morphological changes were monitored by SEM, ex situ XRD and high-energy in situ XRD. Findings: Zirconia particles (0.4-4.3 μm in diameter, 5-10% standard deviation) synthesized according to the modified sol-gel approaches yielded significantly improved monodispersities. As-synthesized amorphous particles transformed to the tetragonal phase at ∼450 °C with a volume decrease of up to ∼75% and then to monoclinic after heating from ∼650 to 850 °C. Submicron particles disintegrated at ∼850 °C and microparticles at ∼1200 °C due to grain growth. In situ XRD revealed that the transition from the amorphous to tetragonal phase was accompanied by relief in microstrain and the transition from tetragonal to monoclinic was correlated with the tetragonal grain size. Early crystallization and smaller initial grain sizes, which depend on the precursors used for particle synthesis, coincided with higher stability. Yttria-doping reduced grain growth, stabilized the tetragonal phase, and significantly improved the thermal stability of the particles.

SYNTHESIS OF YTTRIA-STABILIZED CUBIC ZIRCONIA NANOCRYSTALS BY ULTRASONIC–MICROWAVE ROUTE

Fabrication and Characterization of Y2O3 Stabilized ZrO2 Films Deposited with Aerosol-Assisted MOCVD

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Preparation and characterization of yttria-stabilized zirconia nanotubes

Hydrothermal Synthesis and Characterization of Zirconia Nanocrystallites

Internal Nano Voids in Yttria-Stabilised Zirconia (YSZ) Powder

Preparation and characterization of yttria stabilized zirconia nanoarrays

Zro2 and Ysz Thin-Films Synthesized by Microwave Plasma Cvd Process

Synthesis and Characteristics of Nanocrystalline YSZ by Homogeneous Precipitation and Its Electrical Properties

Conventional sintering of nano-crystalline Yttria-Stabilized Zirconia enables high-strength, highly translucent and opalescent dental ceramics

Preparation and Electronic Properties of Nanometer YSZ

Synthesis and thermal stability of zirconia and yttria-stabilized zirconia microspheres

Influence of Synthesis Routes on the Performance from Weakly Agglomerated Yttria-Stabilized Zirconia Nanomaterials

Crystal phase study of stabilized zirconia collected by dust catcher during airflow pulverization

Synthesis of Yttrium Oxide Nanocrystal Via Solvothermal Process

Facile Synthesis of Highly-dispersed Yttria-doped Zirconia Nanoparticles

Microwave Assisted Preparation of YAG and Yb:YAG Transparent Ceramic Nanopowders for Laser Crystal

Grain Growth Characteristics of Hydrothermally Prepared Yttria Stabilized Zirconia Nanocrystals during Calcination

Ethanol-induced formation of precursor for 8mol% Yttria-stabilized zirconia: Towards the production of well-dispersed, easily sintering, and high-conductivity nano-powders

Effect of dopant concentration on femtosecond pulsed laser irradiation of yttria-stabilized zirconia for generating nanopores

Optimization of the structure and morphology of monoclinic phase nanoscale zirconium dioxide