Abstract:Microstructure evolution, phase determination, phase decomposition and transition of mechanically alloyed Al0.8Co0.5Cr1.5CuFeNi during 950-1150 t high temperature sintering, and the effect of sintered microstructures on mechanical properties were investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). Cu separation occurred first, needle-like Cu rich precipitation in the BCC matrix formed the nucle-ation sites of Al-Ni rich decomposition, while fine lath separation and Cu rich decomposition region sur-rounding the FCC matrix were formed in the FCC matrix, and the remaining FCC matrix formed L12 order. Ordered Al-Ni rich decomposition in BCC matrix appeared after 1000 t sintering. As sintering tempera-ture increased, Al-Ni rich decomposition increased and coarsened and length-width ratio increased. a phase precipitated after 950 t, 1000 t and 1050 t sintering, and disappeared as sintering temperature was higher than 1100 t. Yield strength of sintered alloy decreased from 1445.9 MPa to 1151.5 MPa, and hardness decreased from 714.2 HV to 536.3 HV as sintering temperature increased. The significant increase in plasticity after 1100 t and 1150 t was due to dissolution of a phase. Dislocation accumula-tion around a phase caused development of micro cracks and reduced the plasticity.(c) 2022 Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (http:// creativecommons.org/licenses/by-nc-nd/4.0/).

Formation and Evolution of Oxide Strengthening Phase in Iron-Based Superalloy

Unveiling the Precipitation Behavior and Mechanical Properties in G-phase Strengthened CrFe2Ni2Ti0.2Six Multi-Principal Element Alloys

Unveiling the phase evolution and mechanical properties of Ni1.5Co1.5CrTix alloys with ultrafine/nano structure

The Effect of Simultaneous Si and Ti/Mo Alloying on High-Temperature Strength of Fe3Al-Based Iron Aluminides

Microstructure evolution, phase decomposition and transition of Al0.8Co0.5Cr1.5CuFeNi HEA during high temperature sintering and mechanical properties corresponding to different microstructures

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Effect of Ti and Al on Microstructure and Partitioning Behavior of Alloying Elements in Ni-based Powder Metallurgy Superalloys

Investigation on the Microstructural Evolution and Precipitation Hardening Mechanism of 1cr15ni36w3ti Superalloy with Varied C Contents

The Effect of Y/Ti Ratio on Oxide Precipitate Evolution in ODS Fe-14 Wt Pct Cr Alloys

Phase, Composition and Structure Changes of CoCrNi-Based Concentrated Alloys Resulting from High Temperature Oxidation

Effect of Sintering Temperature on Microstructure and Hardness of W-10Ti Alloy

Effects of Ti Addition and Heat Treatment on the Microstructure and Mechanical Properties of NiAl-Cr(Mo) Hypereutectic Alloy

Phase transformation and strengthening of the gas-atomized FeCoCrNiMo0.5Al1.3 high-entropy alloy powder during annealing

Precipitation Response and Hardening Behaviors of Fe-modified Ti5553 Alloy

The role of the ω phase on the microstructure evolution of precipitation and mechanical property in Ti-3Al-5Mo-4Cr-2Zr-1Fe

Formation of hypoeutectic structure and strengthening mechanism of Co4Cr1.5Fe1.5Ni5 high entropy alloy alloyed by Al

Study on the formation mechanism of Y-Ti-O oxides during mechanical milling and annealing treatment

Studies on thermodynamic and kinetic and phase evolution of W-Ni-Fe powder during mechanical alloying

Effects of Zr, Al, Al+Zr Addition on Phase Evolution Characteristics and Strengthening Mechanisms of Fe‐42Ni‐2Y2O3 ODS Steels Developed by Mechanical Alloying and Spark Plasma Sintering

Doping N/O Impurities into a MoNbTiWZr Refractory Multi-Principal Element Alloy and the Strengthening Mechanism

Simultaneous gettering of oxygen and chlorine and homogenization of the β phase by rare earth hydride additions to a powder metallurgy Ti-2.25Mo-1.5Fe alloy