Abstract:To enhance the corrosion resistance, biocompatibility and mechanical durability of biomedical titanium alloys, a novel β-Ta2O5 nanoceramic coating was developed using a double glow discharge plasma technique. The surface morphology, phase composition and microstructure of the as-deposited coating were examined by atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The coating exhibits a striated structural pattern along the growth direction, which consists of equiaxed β-Ta2O5 grains, 15-20 nm in diameter in cross-section, showing a strong (001) preferred orientation. The mechanical properties and contact damage resistance of the β-Ta2O5 coating were evaluated by nanoindentation. Additionally, scratch tests were performed to evaluate the adhesion strength between the β-Ta2O5 coating and the Ti-6Al-4V substrate. The β-Ta2O5 coating shows high hardness combined with good resistance to both indentation and scratch damage, thus favoring it for long-term load-bearing application in the human body. Electrochemical behavior of the coating was analyzed in both a 0.9 wt % NaCl solution and Ringer's solution at 37 °C, by various electrochemical analytical techniques, including potentiodynamic polarization, electrochemical impedance spectroscopy, potential of zero charge and Mott-Schottky analysis. Compared with uncoated Ti-6Al-4V and commercially pure tantalum, the β-Ta2O5 coating possesses a more positive Ecorr and lower icorr in both aqueous solutions, which is attributed to the thicker and denser β-Ta2O5 coating that provides more effective protection against corrosive attack. In addition, the β-Ta2O5 coating shows stable impedance behavior over 5 days immersion under both simulated body solutions, corroborated by the capacitance and resistance values extracted from the EIS data. Mott-Schottky analysis reveals that the β-Ta2O5 coating shows n-type semiconductor behavior and its donor density is independent of immersion time in both aqueous solutions. Its donor density is of the order of 1 × 1019 cm-3, which is an order of magnitude less than that of the passive films formed on either commercially pure Ta or uncoated Ti-6Al-4V. Moreover, according to the differences between corrosion potential and potential of zero charge, the β-Ta2O5 coating exhibits a greater propensity to repulse chloride ions than both commercially pure Ta and uncoated Ti-6Al-4V. Therefore, the newly developed coating could be used to protect the surface of biomedical titanium alloys under harsh conditions.

A Study of TaxC1−x Coatings Deposited on Biomedical 316L Stainless Steel by Radio-Frequency Magnetron Sputtering

Preparation and Characterization of TaCxN1 − X Coatings on Biomedical 316L Stainless Steel

Structure And Properties Of Tac(X) Coating On Biomedical 316l Stainless Steel By Rf Magnetron Sputtering

The Effects of Substrate Bias on the Properties of HfC Coatings Deposited by RF Magnetron Sputtering

Wear performance of Ti-based alloy coatings on 316L SS fabricated with the sputtering method: Relevance to biomedical implants

Morphological, mechanical and antibacterial properties of Ti-Cu-N thin films deposited by sputtering DC

Bacterial and corrosion resistance of polytetrafluoroethylene-silver composite coatings by magnetron sputtering

Comparative Investigation on Corrosion Resistance of Stainless Steels Coated with Titanium Nitride, Nitrogen Titanium Carbide and Titanium-Diamond-like Carbon Films

Characterization and blood compatibility of TiCxN1 - x hard coating prepared by plasma electrolytic carbonitriding

Electrochemical Properties of a Novel Β-Ta2o5 Nanoceramic Coating Exposed to Simulated Body Solutions.

Improved Corrosion Resistance of Stainless Steel 316L by Ti Ion Implantation

Properties of Titanium Oxide Coating on MgZn Alloy by Magnetron Sputtering for Stent Application

Microstructure and Properties of Monolayer Ta and Multilayer Ta/Ti/Zr/Ta Coatings Deposited on Biomedical Ti-6Al-4V Alloy by Magnetron Sputtering

Effect of Hafnium Addition on the Microstructure and Property Evolutions of ZrCN Coating Prepared via Physical Vapor Deposition

Corrosion and tribocorrosion behaviors of ternary TiZrN coating on 304 stainless steel prepared by HiPIMS

THE EFFECT OF RATIO OF GAS MIXTURE FOR MECHANICAL PROPERTIES AND CRYSTAL STRUCTURES ON 316L STAINLESS STEEL BIOMATERIAL USING DC SPUTTERING TECHNIQUE

Ti–Cu Coatings Deposited by a Combination of HiPIMS and DC Magnetron Sputtering: The Role of Vacuum Annealing on Cu Diffusion, Microstructure, and Corrosion Resistance

Investigation of anti-corrosion properties of Ti:C gradient layers manufactured in hybrid deposition system

Effects of Titanium-Implanted Dose on the Tribological Properties of 316L Stainless Steel

Effect of Temperature Ramp Rate on the Morphology, Phase and Adhesion Strength of Ag-Ta2O5 Thin Film

Anti-adhesion study of three-dimensional reconstructed carbon coatings