Abstract:Charge balance is one of the most important factors for realizing high performance OLEDs. In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer and the electron transporting layer and thereby controlling the charge carrier supplies in the device. Red OLEDs with improved performance were achieved. Charge balance is one of the most important factors for realizing high performance organic light emitting devices (OLEDs). In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer (HIL) as well as the electron transporting layer (ETL) and thereby controlling the charge carrier supplies in the device. First, we develop a p‐dopant material (PD02), with a lowest unoccupied molecular orbit (LUMO) of −4.63 eV, much shallower than that of the commercial material (PD01) of which the LUMO is −5.04 eV. Nevertheless, this enables us to modulate the supply of holes to the emissive layer through tuning doping concentration. We demonstrate that device performances are significantly improved by employing such a scheme. With a 23% molar doping of PD02, a bottom emission red OLED achieves an external quantum efficiency (EQE) of over 30%, an operating voltage of 3.4 V and a LT95 ~15,000 h at 10 mA/cm2, with a Digital Cinema Initiative P3 (DCI‐P3) chromaticity of CIE (X, Y) = (0.68, 0.32). Moreover, the efficiency roll‐off is suppressed up till ~3500 cd/m2, a desirable feature in display applications. The lateral conductivity of by using such HIL is also found to be much lower than that of PD01, resulting in reduced crosstalk among RGB pixels. Next, a new electron transporting material (ETM‐02) with a deep LUMO of −2.86 eV is also introduced to further optimize the charge balance. Although devices with ETM‐02 shows lower voltage and higher EQE, lifetime is compromised. In order to improve lifetime, additional fine tuning of the charge balance is essential. Finally, a second p‐dopant PD03 with a LUMO of −4.91 eV is added to the HIL to further extend the modulation flexibility in the hole injection. A double‐layer HIL consisting of 8 nm of HTM:16% PD02 and 2 nm of HTM:3% PD03, where the former is in contact with anode, is adopted in the device structure. The bottom emission deep red device achieve EQE over 30%, an operating voltage of 3.2 V and an improved LT95 ~13,000 h at 10 mA/cm2 with a BT.2020 range chromaticity of CIE (X, Y) = (0.701, 0.299). In the double HIL configuration, the introduction of PD03 provides one more parameter for tuning and therefore improves the overall device performances.

ReOx charge injection/blocking layers in organic electronic devices

Effects of Organic/Organic Interface on Recombination Efficiency in Double-Layer Organic Diodes

N-Type Doping in Organic Electronic Devices

Lithium Cobalt Oxide As Electron Injection Material for High Performance Organic Light-Emitting Diodes

Organic Radicals Outperform LiF as Efficient Electron-Injection Materials for Organic Light-Emitting Diodes.

Improving the Performance of Red Organic Light-Emitting Transistors by Utilizing a High-k Organic/Inorganic Bilayer Dielectric.

Inverted device architecture for high efficiency single-layer organic light-emitting diodes with imbalanced charge transport

Using an Organic Radical Precursor As an Electron Injection Material for Efficient and Stable Organic Light-Emitting Diodes

Charge balance in OLEDs: Optimization of hole injection layer using novel p‐dopants

Integrated Quasi‐2D Perovskite/Organic Solar Cells with Efficiency over 19% Promoted by Interface Passivation

A multicomponent rhenium-based triplet emitter for organic electroluminescence

Improving Electron Injection of Organic Light-Emitting Transistors via Interface Layer Design

Charge injection engineering at organic/inorganic heterointerfaces for high-efficiency and fast-response perovskite light-emitting diodes

Reduced non-radiative charge recombination enables organic photovoltaic cell approaching 19% efficiency

High performance ZnO cathode interface doped by organic electrolyte and inorganic metal ion for organic solar cells

Investigation of Novel Efficient Electron Injection Lithium Complex Containing Quinoxaline Moiety for Organic Light-Emitting Diodes

Efficient Solution-Processed Red Organic Light-Emitting Diode Based on an Electron-Donating Building Block of Pyrrolo[3,2-B]pyrrole

In Situ and Ex Situ Investigation of the Organic-Organic Interface Effect

Effects of charge mobilities and exciton blocking capabilities of charge blocking layers on the performance of organic light-emitting diodes

Low-Temperature Evaporable Re2O7: an Efficient P-Dopant for OLEDs

Insights into Redox Processes and Correlated Performance of Organic Carbonyl Electrode Materials in Rechargeable Batteries