Abstract:Charge balance is one of the most important factors for realizing high performance OLEDs. In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer and the electron transporting layer and thereby controlling the charge carrier supplies in the device. Red OLEDs with improved performance were achieved. Charge balance is one of the most important factors for realizing high performance organic light emitting devices (OLEDs). In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer (HIL) as well as the electron transporting layer (ETL) and thereby controlling the charge carrier supplies in the device. First, we develop a p‐dopant material (PD02), with a lowest unoccupied molecular orbit (LUMO) of −4.63 eV, much shallower than that of the commercial material (PD01) of which the LUMO is −5.04 eV. Nevertheless, this enables us to modulate the supply of holes to the emissive layer through tuning doping concentration. We demonstrate that device performances are significantly improved by employing such a scheme. With a 23% molar doping of PD02, a bottom emission red OLED achieves an external quantum efficiency (EQE) of over 30%, an operating voltage of 3.4 V and a LT95 ~15,000 h at 10 mA/cm2, with a Digital Cinema Initiative P3 (DCI‐P3) chromaticity of CIE (X, Y) = (0.68, 0.32). Moreover, the efficiency roll‐off is suppressed up till ~3500 cd/m2, a desirable feature in display applications. The lateral conductivity of by using such HIL is also found to be much lower than that of PD01, resulting in reduced crosstalk among RGB pixels. Next, a new electron transporting material (ETM‐02) with a deep LUMO of −2.86 eV is also introduced to further optimize the charge balance. Although devices with ETM‐02 shows lower voltage and higher EQE, lifetime is compromised. In order to improve lifetime, additional fine tuning of the charge balance is essential. Finally, a second p‐dopant PD03 with a LUMO of −4.91 eV is added to the HIL to further extend the modulation flexibility in the hole injection. A double‐layer HIL consisting of 8 nm of HTM:16% PD02 and 2 nm of HTM:3% PD03, where the former is in contact with anode, is adopted in the device structure. The bottom emission deep red device achieve EQE over 30%, an operating voltage of 3.2 V and an improved LT95 ~13,000 h at 10 mA/cm2 with a BT.2020 range chromaticity of CIE (X, Y) = (0.701, 0.299). In the double HIL configuration, the introduction of PD03 provides one more parameter for tuning and therefore improves the overall device performances.

Improving the Performance of Red Organic Light-Emitting Transistors by Utilizing a High-k Organic/Inorganic Bilayer Dielectric.

Organic Light-Emitting Field-Effect Transistors: Device Geometries and Fabrication Techniques

High-Performance Light-Emitting Diodes Based on Carbene-Metal-Amides

Highly Efficient Flexible Organic Light Emitting Transistor Based on High‐k Polymer Gate Dielectric

Improving the Efficiency of Multilayer Organic Light‐Emitting Transistors by Exploring the Hole Blocking Effect

Van der Waals Multi‐Layer Heterojunction for Low‐Voltage Organic RGB Area‐Emitting Transistor Array

Achieving Bright Organic Light Emitting Field Effect Transistors with Sustained Efficiency through Hybrid Contact Design

Organic electroluminescence from photovoltaic thin film

Highly Efficient Nondoped Green Organic Light-Emitting Diodes with Combination of High Photoluminescence and High Exciton Utilization

Redistributed Current Density in Lateral Organic Light‐Emitting Transistors Enabling Uniform Area Emission with Good Stability and Arbitrary Tunability

En Route to Wide Area Emitting Organic Light‐Emitting Transistors for Intrinsic Drive‐Integrated Display Applications: A Comprehensive Review

Host-Free Deep-Blue Organic Light-Emitting Transistors Based on a Novel Fluorescent Emitter.

Significant Light Extraction and Power Efficiency Enhancement of Organic Light Emitting Diodes by Subwavelength Dielectric-Nanomesh Using Large-area Nanoimprint

Improved Performance of Organic Light-Emitting Transistors Enabled by Polyurethane Gate Dielectric

Organic Light‐Emitting Transistors Entering a New Development Stage

Improving Electron Injection of Organic Light-Emitting Transistors via Interface Layer Design

Inverted device architecture for high efficiency single-layer organic light-emitting diodes with imbalanced charge transport

Highly Efficient Organic Blue Electroluminescent Materials and Devices with Mesoscopic Structures

11.1: Invited Paper: High Performance Deep Red OLEDs Using Dual p‐dopants to Control Hole Injection

High‐efficiency Area‐Emissive White Organic Light‐Emitting Transistor for Full‐Color Display

Charge balance in OLEDs: Optimization of hole injection layer using novel p‐dopants