Abstract:Fe-29Al-2Cr powders with nanoscale grain sizes were produced by mechanical milling of prealloyed intermetallic powders. A consolidation procedure employing high-pressure, low strain rate hot forging (sinter-forging) has been developed to consolidate the powders into full-density compacts. The relative density and average grain size of the compact have been studied as a function of consolidation temperature at constant pressure. Fully dense compacts (>99.5% theoretical density) were produced at a relatively low temperature of 545 degrees C with a pressure of 1.25 GPa. Transmission electron microscopy and x-ray diffraction analysis indicate that the average grain size has been maintained to the order of 30 nm in samples consolidated under these conditions. By using protective Ar atmosphere during mechanical milling and consolidation, contamination of oxygen and carbon in consolidated samples has been controlled to below a small fraction of an atomic percent. Microhardness tests of nanocrystalline Fe-29Al-2Cr samples indicate a significant strengthening effect due to grain size refinement and a monotonic hardness increase with decreasing residual porosity. Our work demonstrates the feasibility of using mechanically milled powders as the source of nanocrystalline materials for the production of fully dense, low-impurity, nanocrystalline bulk samples needed for reliable mechanical property measurements and practical applications.

Study on hot-hydrostatic extrusion of mechanically alloyed nanocrystalline Cu-5%Cr powders

Fabrication of High Strength Conductivity Submicron Crystalline Cu-5%Cr Alloy by Mechanical Alloying

Densification of Cu-15wt%Cr composite powders prepared by mechanical milling

Effect of Extrusion on Microstructure and Properties of a Submicron Crystalline Cu–5 Wt.%cr Alloy

Structure and properties of the mechanically alloyed Cu-5Cr alloy

Hot hydrostatic extrusion of mechanically alloyed Al-4.9Fe-4.9Ni powders

Full-density nanocrystalline Fe-29Al-2Cr intermetallic consolidated from mechanically milled powders

Consolidation of Nanocrystalline Al-Ti Alloy Powders Synthesized by Mechanical Alloying

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Microstructures and properties of cold drawn submicron crystalline Cu-5wt%Cr material

Effects of Deformation on Microstructures and Properties of Submicron Crystalline Cu-5%Cr Alloy

Thermal stability of the mechanically alloyed Al-10Ti nanocrystalline alloy during consolidation process

Microstructure and Mechanical Properties of Ultrafine Grained CoCrFeNi and CoCrFeNiAl0.3 High Entropy Alloys Reinforced with Cr2O3/Al2O3 Nanoparticles

Nanophase Fe Alloys Consolidated to Full Density from Mechanically Milled Powders

Study on Microstructure and Properties of Cu-Zr Alloy Prepared by Mechanical Alloying

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion

Deformation Processed Cu-15 Wt Pct Cr Composite Synthesized by Hot Hydrostatic Extrusion of Mechanical Milled Powders

Microstructure and Mechanical Properties of a Hot-Hydrostatically Extruded 93w–4.9ni–2.1fe Alloy

Super High Strength Aluminum Alloy Processed By Mechanical Alloying And Hot Extrusion

Microstructure and Mechanical Properties of a Bulk Ultrafine Grained Al–7Si–0.3Mg Alloy Produced by Thermomechanical Consolidation of a Nanocrystalline Powder