Abstract:Fiber-optic temperature sensors have gained much attention owing to their intrinsic features of light weight, immunity to electromagnetic interference, and capability for distributed measurement. Especially, temperature sensors based on Fabry-Perot interferometers (FPIs) are attractive owing to their advantages of compact size and convenient reflection measurement. However, due to the low thermal expansion or/and thermo-optic coefficient of fiber, the temperature sensitivities of these sensors are normally low (similar to 10 pm/degrees C or even lower). In order to improve the temperature sensitivity, a device with dual cascaded FPIs is proposed and demonstrated in this paper, which works on vernier effect and exhibits a much higher temperature sensitivity. The device is fabricated by splicing a short segment of large mode area (LMA) fiber to a short segment of capillary tube fused with a section of single-mode fiber to form an extrinsic Fabry-Perot interferometer with a glass cavity cascaded to an intrinsic FPI with a narrow air cavity. By setting the lengths of capillary tube and LMA fiber to allow similar free spectral ranges to be obtained, and superimposing of the reflection spectra of the two FPIs, the vernier effect can be generated. Firstly, the principle of temperature sensing based on vernier effect of this device is analyzed and simulated theoretically, and it is found that the temperature sensitivity can be improved significantly by using vernier effect compared with that of a single FPI with an air-cavity or glass cavity by directly tracing resonant dips/peaks. Then, the temperature responses of the FPI with single air-cavity and dual cascaded cavities are measured, respectively. Experimental results match well with the theoretical analysis carried out. The temperature sensitivity of the proposed sensor is improved greatly from 0.71 pm/degrees C for a single FPI sensor with an air-cavity to 179.30 pm/degrees C by employing the vernier effect. Additionally, the sensor exhibits good repeatability in a temperature range of 100-500. C. The proposed sensor has the advantages of compact size ( < 1 mm in dimension) and high sensitivity, which makes it promising for temperature sensing in a variety of industries, such as food inspection, pharmacy, oil/gas exploration, environment, and high-voltage power systems.

Fiber-Optic Fabry-Pérot Sensor Based on Periodic Focusing Effect of Graded-Index Multimode Fibers

Sensitivity-enhanced Optical Sensor Based on Multilayer Coated Fabry–Pérot Interferometer

Femtosecond laser direct writing of long period fiber grating sensor with high refractive index sensitivity

Few-mode fiber-embedded long-period fiber grating for simultaneous measurement of refractive index and temperature

Refractive index and temperature sensors based on no-core fiber cascaded with long period fiber grating

High Sensitivity Refractometer Based on Tapering Two-Mode Fiber Embedded Long-Period Fiber Grating

Temperature-insensitive refractive index sensor based on high-order-resonance short-line long-period fiber grating

High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method

Fiber-Taper Seeded Long-Period Grating Pair As A Highly Sensitive Refractive-Index Sensor

High Sensitive Refractive Index Sensor Based on Dispersion Turning Point Long-Period Fiber Gratings in Tapered Fiber

High sensitivity fiber optic temperature sensor based on CTFBG-FPI and vernier effect

A Multiparameter Sensor Based on Dumbbell-Shaped Double-Cladding Fiber Structure Cascaded Long Period Fiber Grating

High-sensitivity Double-Parameter Sensor Based on the Fibre-Tip Fabry–Pérot Interferometer

Sensitivity-enhanced temperature sensor with fiber optic Fabry-Perot interferometer based on vernier effect

Temperature-compensated high-sensitivity refractive index, liquid level and PH sensing realization enabled by a small-period microfiber long period grating cascaded with microfiber Bragg grating

Refractive Index Sensing Characteristic of A Hybrid-Fabry-Perot Interferometer Based on an In-Fiber Ellipsoidal Cavity

A fiber air-gap Fabry–Pérot temperature sensor demodulated by using frequency modulated continuous wave

Compact refractive index sensor based on offset splicing long-period fiber grating

Reflective Optical Fiber Sensors Based on Tilted Fiber Bragg Gratings Fabricated With Femtosecond Laser

Simultaneous Temperature and Force Measurement Using Fabry-Perot Interferometer and Bandgap Effect of a Fluid-Filled Photonic Crystal Fiber.