Abstract:In the aerospace field, aiming at the requirements of thermal response monitoring of composite structures in space service environment, a monitoring method for carbon fiber honeycomb sandwich structure based on fiber Bragg grating (FBG) reflection spectrum characteristics analysis under different thermal loads was studied. The fiber Bragg grating (FBG) sensors were implanted in different layers of carbon fiber honeycomb sandwich structure respectively. By monitoring the fiber Bragg grating (FBG) reflection spectrums of each layer under different thermal loads, the associated thermal strain characteristics of the honeycomb sandwich structure can be obtained. The results show that, certain differences exist in the thermal strain characteristics of different material layers in the carbon fiber honeycomb sandwich structure. As the temperature increases, the center wavelength of reflection spectrum of fiber Bragg grating (FBG) implanted between the outer skin surface and the glass cloth shifts to the long wave direction and the waveform of the obtained reflection spectrum changes insignificantly. As the temperature decreases, the reflection spectrum of fiber Bragg grating (FBG) implanted between the second and the third layers of the carbon fabric prepreg appears chirp effects gradually, such as sidelobe, multi-peak, etc. The main-peak center wavelength and the right sub-peak center wavelength of the reflection spectrum both shift to the short wave direction gradually. The peak amplitude of the main-peak does not show significant change and its temperature sensitivity is about 5. 56 X 10(-3) dBm . degrees C-1. The peak amplitude of the right sub-peak increases significantly and its temperature sensitivity is about 40. 32 X 10(-3) dBm . degrees C-1. The full width at half maximum(FWHM)of reflection spectrum of fiber Bragg grating (FBG) implanted between the inner skin and the honeycomb core increases gradually at a rate of 3. 19 pm . degrees C-1 with the temperature decreasing. The reflection spectrum appears a multi-peak trend significantly due to the uneven thermal stress distributed between the layers. The interlaminar thermal strain of each implanted layer increases in similar trends within the increasing temperature range of - 70 degrees C to +60 degrees C. But at the temperature range of +60 degrees C to +120 degrees C, the changing trend of the interlaminar thermal strain between each implanted layers shows significant differences. These characteristics can provide useful help to the following on-orbit status monitoring of composite spacecraft structure in space environment.

Application of Fiber Bragg Grating Sensors in Monitoring Curing Process of Carbon Fiber Composite

In-situ monitoring of carbon fiber/epoxy composite with FBG sensors under curing and thermal cycling conditions

Simultaneous measurement of strain and temperature during and after cure of unsymmetric composite laminate using fiber-optic sensors

Measurement of process-induced stresses in composite laminates by FBG sensors

Technology and test of fiber Bragg grating in composite materials

Research On Measurement Of Fiber Bragg Grating Considering The Cross-Sensitivity Of Temperature And Strain

Applications of Fiber Bragg Grating Sensors in the Composite Industry

A single three-parameter tilted fibre Bragg grating sensor to monitor the thermosetting composite curing process

Structural Nde of Cfrp Composite Materials Using Fiber Bragg Grating Sensors

Real-time strain monitoring and control of urban bridge cluster monitoring system with FBG sensor

Fiber Bragg Grating Sensors toward Structural Health Monitoring in Composite Materials: Challenges and Solutions

Magnetic Fiber Enabled Curing Electrogram: Real-time Process Monitoring for Thermosetting Polymer Materials

Embedded fibre Bragg grating sensors for non-uniform strain sensing in composite structures

Temperature-controlled Fiber Bragg Grating Dynamic Strain Detection System

Fiber Bragg grating temperature sensor for marine application

Strain Measurement for Composite Materials During Mechanical Testing Based on Fiber Bragg Grating Monitoring

Research on Thermal Load Response Spectrum of FBG Sensors Implanted in Carbon Fiber Honeycomb Sandwich Structure

A Method of Strain Measurement Based on Fiber Bragg Grating Sensors

Fiber-optic Composite Cure Sensor: Monitoring the Curing Process of Composite Material Based on Intensity Modulation

Review on composite structural health monitoring based on fiber Bragg grating sensing principle