Abstract:This work presents the experimental results of narrow gap butt welding of steel plates with large thickness by using the Metal Active Gas (MAG) welding method.The typical defects are accompanied with this process such as the infusion in the side wall and the porosity due to the narrow gap which affect on the melting process. Thus, some publications noted the results of welding for the thickness up to 20−30 mm and the chamfer angle about 30° using GMAW/MIG, GTAW/TIG, SMAW and new development such as laser – arc hybrid, laser multi- pass technique, super -TIG welding etc. But the production requires the solution to save the costs by the reduction of time, labour and investment keeping the standard quality. That is the aim of this study. In order to improve the quality of weld joint and increase the productivity of the process, is it suggested to develop the innovative welding process, in which the welding voltage – Uw, the translational velocity of the tip – Vt, and rotational velocity of the tip – Vr, are changing. This helped to increase the thickness of steel plates up to 50 mm and the chamfer angle decreased at 15°, providing the satisfied quality of the weld. The micrography study serve as the preliminary proof of this hypothesis. The microstructures in 4 regions, such as the weld center zone, heat-affected zone (HAZ), parent metal region, and the boundary between the weld metal and the HAZ were examined. The microstructures of 13 positions from different experiments are investigated using the optical microscope (Axiovert 25).These experiments covered all specific points (node) locating accordingly to three layers from bottom to top of the weld joint . The findings proved the welding quality is similar in case of narrow gap but the chamfer angle is twice lower and the thickness is increased. The result of the study enhances the productivity due to saving the labour cost and the welding materials. It is recommended to consider the effect of other factors (such as cooling conditions, dwell time when the arc approaching the side walls) to optimize the weld quality. There is the huge volume of the heavy steel constructions with the thick steel construction and specific narrow gap in industry. The results of this study with the optimization and more deeper evaluation the influence of main parameters of welding process to eliminate the typical defects will be the valuable reco mmendation for the managers and engineers in the production of metallic constructions

Rotating arc horizontal narrow gap welding of high strength quenched and tempered steel

An Innovative Methodology in Narrow Gap GTAW for Alternating Magnetic Field with Synchronous Swing of Filler Wire and Arc

Investigation of Microstructure and Mechanical Properties of High-Depth-to-Width-Ratio Horizontal NG-GMAW Joint for S500Q Steel

Achieving Equal Strength Joint to Parent Metal in a Friction Stir Welded Ultra-High Strength Quenching and Partitioning Steel

Comparison of Microstructure and Mechanical Properties of Ultra-Narrow Gap Metal Active Gas Arc Welded and Narrow Gap Submerged Arc Welded Q235A Low Carbon Steel

Numerical simulation on molten pool behavior of narrow gap gas tungsten arc welding

Microstructure and mechanical properties of T-joints in mid-thick Q345 steel plates welded using deep penetration tungsten inert gas welding

Stirring effect of the rotating arc on the molten pool during non-axisymmetric tungsten NG-GTAW

Building automatic welding process using a high-performance steel submerged q460gjc

Research on the Welding Process and Weld Formation in Multiple Solid-Flux Cored Wires Arc Hybrid Welding Process for Q960E Ultrahigh-Strength Steel

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

A novel high efficiency narrow-gap laser welding technology of 120 mm high-strength steel

The evaluation on performance of narrow- gap welding thick steel plates under the influence of main welding parameters

Microstructure and Mechanical Properties of Narrow Gap Laser-Arc Hybrid Welded 40 mm Thick Mild Steel

Studies on Mechanism of Zigzag Crack Forming Process in Weld Metal of Narrow Gap Submerged Arc Welding of Thick Plate

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Experimental and Simulation Study on Welding Characteristics and Parameters of Gas Metal Arc Welding for Q345qD Thick-Plate Steel

A Laser-Induced TIG Arc Narrow-Gap Welding Technique for TC4 Titanium Alloy Thick Plates Based on the Spatial Position Control of Laser, Arc and Filler Wire

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

Improvement of the welded joints properties of P460NH steel with AC-assisted GTAW arc

Optimization of microstructure and properties of thick Al alloy welded joints for one-step formation by keyhole welding