Abstract:Aiming to obtain a martensite-free microstructure of Ti–Zr alloys with a combination of enhanced deformability and improved mechanical properties for dental application, two high Zr-containing Ti-based alloys were prepared with commercially pure titanium as a control. The effects of Zr addition on the deformation mechanism, microstructure and mechanical properties were investigated. After thermo-mechanical processing and cold deformation, samples were characterized using Vickers microhardness, tensile tests, X-ray diffraction (XRD) scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The XRD and TEM examinations revealed that the increasing Zr addition suppressed the deformation twining and favored the deformation-induced face-centered cubic (FCC) phase, the corresponding reason was discussed. There is a competition between the deformation twin and FCC phase. The two types of FCC phase were simultaneously found with orientation relationships (ORs) of Basal-type: <11–20>HCP//<110>FCC and {0001}HCP//{111}FCC and Prismatic-type: <0001>HCP//<001>FCC and {10-10}HCP//{110}FCC. This phase transformation enhanced the deformability during processing. As the Zr addition increased, the microhardness, mechanical strength and plasticity are increased concurrently. The interactions of twins were found to cause brittle fracture of Ti20Zr alloy. Based on the texture analysis, the activated slip systems of FCC phase were determined via calculating the Schmid factor. The FCC phase not only provided additional slip systems but also impeded dislocation slip effectively, improving the strength-plasticity of Ti30Zr alloy. The findings will provide a novel approach associated with the strengthening-toughening mechanism of metallic materials.

Transitional dynamics of deformation induced phase transformation at ZrC/austenitic interface

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Effects of Deforming Temperature on Grain-refining of 20Mn2 Steel Containing ZrC Particles

Strengthening Effect of ZrC Particles on Low-Carbon Microalloy Steel

Effect of Zr on static recrystallization of deformed austenite and strain-induced precipitation in Ti microalloyed steel

Microstructural evolution during the austenite-to-ferrite transformation from deformed austenite

Influence of Thermomechanical Control Process on the Evolution of Austenite Grain Size in a Low-Carbon Nb-Ti-Bearing Bainitic Steel

Effect of ZrC Particle on Grain Refining and Properties of Low-Carbon and Low-Alloy Steel

Effect of Zr Treatment on Inclusion and Solidification Microstructure in Ti Deoxidized Low Carbon Microalloyed Steel

Effects of Zr on high temperature deformation and dynamic precipitation of laves phase in Fe–13Cr–5Al–2Mo–0.5Nb–0.4Ta alloy

Influence of Austenite Deformation on Ferrite Growth in a Fe–C–Mn Alloy

Effect of Zr addition on the microstructure, phase transformation and mechanical property of Ni 50 Mn 25 Ga 17 Cu 8 alloy

Deformation behavior and Microstructural evolution of Zr‐Sn‐Nb‐Fe alloy over a wide temperature range based on the law of mixture

Influence of Deforming Temperatures on the Strain Induced Transformation in Q235 Plain Carbon Steel

Effect of Austenitization Conditions on the Transformation Behavior of Low Carbon Steel Containing Ti⁻Ca Oxide Particles

Hot Deformation Behavior and Microstructure Evolution of a Novel High-Zn Containing Al-Zn-Mg-Cu-Zr Alloy

Zr addition-induced transitions of deformation mechanism at high temperatures of Nb-Si-Ti based multi-alloys: Super-dislocations in γ-Nb 5 Si 3

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Effect of zirconium addition on the austenite grain coarsening behavior and mechanical properties of 900 MPa low carbon bainite steel

Evolution of (ti, Mo)C Particles in Austenite of a Ti–Mo-bearing Steel