Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Dynamic Deformation Behavior Experiments of Alloy Galvanized Deep Drawing Steel Sheet for Automobile and Simulation

Dynamic tests and constitutive model for 7075-T6 aluminum alloy

Research on dynamic deformation behavior and constitutive relationship of hot forming high strength steel

0610 A Comparative Study on Gao-Zhang and Johnson-Cook Constitutive Models

The Dynamic Mechanics Performance And Constitutive Model Of 30crmnsia High Strength Alloy Steel

Dynamic Constitutive Behavior Investigation of a Novel Low Alloy Ultra-High Strength Steel

Effect of Material Anisotropy on the Mechanical Response of Automotive Steel under High Strain Rates

Dynamic Mechanical Behavior and Numerical Simulation of 6013-T4 Aluminum Alloy at Different Temperatures and Strain Rates

Effect of Loading Rate on Tensile Properties of Automotive Steel Sheet

Dynamic Compression and Constitutive Model in Fe-27Mn-10Al-1C Duplex Lightweight Steel

A High-Accuracy Dynamic Constitutive Relation of Die-Cast Alâ¿¿Si Aluminium Alloy

Research on the Dynamic Deformation Behavior of the DP780 Advanced High Strength Steel

Dynamic deformation behavior and corresponding constitutive model of ultra-high strength DP1000 steel

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Dynamic Constitutive Model of Q235B Steel and Its Application in LS-DYNA

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al–Cu–Mn–Fe–Zr Alloy during Warm Deformation

Experimental Research on Strain Rate Sensitivity of Automotive Steel Sheet

The Testing and Behaviour Modelling of Sheet Metals at Strain Rates from 10−4 to 104 S−1

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

Dynamic Tensile Behaviour and Full Field Strain Measurement of High Strength Steel

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy