Abstract:A recently developed single shear specimen (SSS) was used to investigate the thermo-viscoplastic behavior of 2024-T351 aluminum alloy (AA2024-T351) under simple shear stress state. Shear stress-shear strain relations over a wide range of strain rates, covering low (0.001 and 0.1 sâˆ’1), medium (10 sâˆ’1), high (3000 and 6000 sâˆ’1) and very high (14000-49000 sâˆ’1) regimes and at initial temperatures from 293 to 573 K were obtained experimentally. The results show that: (1) at 293 K, AA2024-T351 exhibited negligible strain rate sensitivity at strain rates below 6000 sâˆ’1, and the effect of strain rate became obvious at strain rates above 14000 sâˆ’1; (2) dynamic strain aging (DSA) occurred at temperatures between 373 and 573 K and strain rates below 6000 sâˆ’1; (3) strain rate sensitivity of the material was strongly affected by DSA, and bell-shaped strain rate sensitivity curves were observed; (4) with an increase in temperature, peak values of the bell-shaped strain rate sensitivity curves shifted to higher strain rates. A constitutive model taking the advantages of Johnson-Cook model, Khan-Huang-Liang model, Nemat-Nasser-Li model and Wang-Guo-Gao model was developed for deformation behavior description, with the effects of viscous drag on dislocation motion and DSA considered. The experimental flow stress curves were compared to the model predictions, and a good agreement was observed. To validate the constitutive model independently of the experiments used for the identification of the model parameters, numerical simulations of Taylor impact tests were performed. A good agreement between experimental and numerical post-test specimens, in terms of mushroom shaped specimen head and reduced specimen length, was observed. According to the numerical results, strain rates varied largely between 103 and 106 sâˆ’1 during Taylor impact tests. Besides, numerical simulations of Taylor impact tests were performed again using the constitutive model excluding the viscous drag component, and less accurate numerical results were obtained. It implies that for precise computations of engineering applications, the actual strain rate should be considered in the establishment of constitutive models.

Dynamic constitutive model and deformation mechanism of 2219 aluminum alloy based on the dynamic interruption‐recovery

A Physically Based Constitutive Model and Continuous Dynamic Recrystallization Behavior Analysis of 2219 Aluminum Alloy during Hot Deformation Process

Strain Rate Sensitivity and Adiabatic Shear Deformation of an Advanced Al-Mg Alloy

Static Softening Behavior and Modified Kinetics of Al 2219 Alloy Based on a Double-Pass Hot Compression Test

Dynamic Compression and Constitutive Model in Fe-27Mn-10Al-1C Duplex Lightweight Steel

Dynamic Recrystallization Critical Conditions and a Physically–Based Constitutive Model of Al–4.8Mg Alloy Under Hot Working Conditions

Study on Dynamic Impact Response and Optimal Constitutive Model of Al-Mg-Si Aluminum Alloy

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions

The dynamic compressive behavior and constitutive models of a near α TA23 titanium alloy

Microstructural Evolutions of AA7055 Aluminum Alloy under Dynamic and Quasi-static Compressions

Dynamic recrystallization mechanisms of as-forged Al–Zn–Mg-(Cu) aluminum alloy during hot comp.ression deformation

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Constitutive Analysis and Microstructure Characteristics of As-Homogenized 2198 Al–Li Alloy under Different Hot Compression Deformation Conditions

Microstructure Evolution and Dynamic Recrystallized Model of 5083 Aluminum Alloy During Hot Deformation

Constitutive modeling of deformation in high temperature of a forging 6005A aluminum alloy

Deformation Behavior and Constitutive Model for High Temperature Compression of a Newly Type of Ni3Al‐based Superalloy

The Study on Forming Property at High Temperature and Processing Map of 2219 Aluminum Alloy

Simple shear behavior of 2024-T351 aluminum alloy over a wide range of strain rates and temperatures: Experiments and constitutive modeling

The Constitutive Responses of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates and Elevated Temperatures

Dynamic Softening Mechanism and an Improved Unified Constitutive Model for an Al–Cu–Mn–Fe–Zr Alloy during Warm Deformation