Abstract:Solid oxide fuel cell (SOFC) is an energy conversion device that converts chemical energy in fuels into electric energy directly with the advantages of high efficient, clean, and wide fuel adaptability. Most hydrocarbons such as natural gas, ethane and bio-oil can be used as fuels in SOFC. When a hydrocarbon fuel, such as methane (CH4), is directly used for IT-SOFCs without prereforming by adding oxygen, steam or carbon dioxide, it is electrochemically oxidized on the triple-phase boundaries (TPB) with a strong tendency of carbon deposition in the traditional Ni-based anode. In this paper, we introduce an extra internal reforming layer on the surface of anode-support. The layer of a LaCrO3 based perovskite with exsolved Ni nanoparticles catalyst (La0.6Sr0.2Cr0.85Ni0.15O3 showed high stability in reducing atmosphere and excellent catalytic performance. Based on this, two types of anode-supported cell are fabricated by tape casting, screen printing and sintering processes. The first one is a conventional anode supported cell with a configuration of Ni-GDC/GDC/GDC-LSCF (cell 1); and the other contains a reforming layer mixed with La0.6Sr0.2Cr0.85Ni0.15O3 and SDC which was a well coking resistant promoters (cell 2). When CH4–CO2 was used as the fuel, which was supposed to yield syngas with the H2–CO ratio close to unity, the polarization resistance of the cell 1 reach at 0.247 Ω cm2 whereas the value of cell 2 is 0.082Ω cm2 at 750 °C. These results implied that both the physical and the chemical properties of the TPB have been altered drastically during internal dry reforming since that Ni-based anode show poor catalytic performance in reforming and are prone to coking. Consequently, the maximum power density for cell 1 was 470 mW cm-2 and the cell suffered from degradations during a 1 h galvanostatic operation at 1 A cm-2. The performances of the cell 2 are significantly increased above the level of the cell 1, demonstrating a peak power density at 929 mW cm-2 at 750 °C and a stable cell voltage at 1 A cm-2 and 750 °C for 48 h. Carbon deposition in the anode region of the tested cell 2 is not detected, as the La0.6Sr0.2Cr0.85Ni0.15O3 is a more active and stable catalyst than the Ni-based anode-support for dry reforming. Finally we demonstrated the strong interaction between the exsolved nanoparticles and the substrate could prevent coking deposition and proposed a promising configuration of double-layer anode for solid oxide fuel cells with on-cell reforming. Figure 1

Direct Flame SOFCs with La[sub 0.75]sr[sub 0.25]cr[sub 0.5]mn[sub 0.5]o[sub 3−δ]∕ni Coimpregnated Yttria-Stabilized Zirconia Anodes Operated on Liquefied Petroleum Gas Flame

A Direct Flame Solid Oxide Fuel Cell for Potential Combined Heat and Power Generation

Performance Characteristics of a Micro-tubular Solid Oxide Fuel Cell Operated with a Fuel-rich Methane Flame

Anode-Supported Micro-SOFC Stacks Operated under Single-Chamber Conditions

Electrical and Stability Performance of Anode-Supported Solid Oxide Fuel Cells with Strontium- and Magnesium-Doped Lanthanum Gallate Thin Electrolyte

A Non-Sealed Solid Oxide Fuel Cell Micro-Stack with Two Gas Channels

Preparation and Properties of Direct-Methane Solid Oxide Fuel Cell Based on a Graded Cu-CeO<sub>2</sub>-Ni-YSZ Composite Anode

Coking-Resistance and Sulfur-Tolerance Study of La0.4Sr0.6Co0.2Fe0.7Nb0.1O3-δ Anode

Experimental Characterization of a Direct Methane Flame Solid Oxide Fuel Cell Power Generation Unit

Performance of the single-chamber solid oxide fuel cell with a La 0.75 Sr0.25 Cr0.5 Mn0.5 O 3-δ -based perovskite anode

Fabrication and Evaluation of a Ni/La0.75Sr0.25Cr0.5Fe0.5O3−δ Co-Impregnated Yttria-Stabilized Zirconia Anode for Single-Chamber Solid Oxide Fuel Cells

La0.6Sr1.4MnO4 Layered Perovskite Anode Material for Intermediate Temperature Solid Oxide Fuel Cells

La0.6Sr0.4Co0.2Fe0.8O3-δ Nanoparticles Modified Ni-based Anode for Direct Methane-Fueled SOFCs

Performance of the Single-Chamber Solid Oxide Fuel Cell with a La(0.75)Sr(0.25)Cr(0.5)Mn(0.5)O(3-delta)-Based Perovskite Anode

Enhanced Performance of Solid Oxide Fuel Cells with Ni/CeO2 Modified La0.75Sr0.25Cr0.5Mn0.5O3− Anodes

Analysis of Gas Leakage and Current Loss of Solid Oxide Fuel Cells by Screen Printing

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

High-performance Ni In-Situ Exsolved Ba(Ce0.9Y0.1)0.8Ni0.2O3-δ/Gd0.1Ce0.9O1.95 Composite Anode for SOFC with Long-Term Stability in Methane Fuel

Direct Operation of Solid Oxide Fuel Cells on Low-Concentration Oxygen-Bearing Coal-Bed Methane with High Stability

Performance of Anode-Supported Single-Chamber Solid Oxide Fuel Cells

A Novel Design of Single-Chamber SOFC Micro-Stack Operated in Methane–oxygen Mixture