Abstract:Material response and the launch of laser plasma during the 1064 nm nanosecond laser pulse induced damage to the exit surface of fused silica are investigated. Employing a polarization-based two-frame shadowgraphy setup with ～ 60 fs probing resolution, the transient material responses from the rising part of nanosecond pumping pulse to several hundred nanosecond timescale are captured. Using a shearing interferometry setup, the evolution of transient phase shift of laser plasma in the expansion process to the ambient air is also investigated. Inhomogeneous distribution of phase shift caused by the electrons and neutrals in the plasma is quantitatively resolved by employing the fast Fourier transform based filtering algorism. To demonstrate the evolutions of important plasma parameters such as pressure, temperature and density, a continuum hydrodynamic model is numerically solved. The initial pressure of plasma is estimated according to the point-explosion model, and the initial plasma temperature is achieved by calculating the difference between simulating shockwave front radius and experimental value at the same delay. The optimal temperature is chosen when the radius difference is minimal. Main conclusions are as follows. 1) Abundant suprathermal electrons are excited in the early energy deposition process. Part of these electrons contribute to the thermal transport process and produce the laser supported solid-state absorption front (LSSAF) which propagates into the bulk silica. Other electrons escape to the air side and contribute to the formation of air plasma through the impact ionization process. Plasma expansion speed is about 20 km/s during this phase. 2) When the pump pulse is terminated, the LSSAF and air plasma lose their energy supplied and experience a rapid decline of the temperature and expansion velocity. As a result, the final damage crater depth exhibits seldomly no increase compared with the transient crater depth during this phase. Hot bulk plasma formed in this phase becomes the damage precursor and induces the ejection of abundant neutrals probably due to the phase explosion mechanism. Inhomogeneous distribution of stress is formed by Rayleigh-Taylor instability at the interface between hot bulk plasma and surrounding bulk material during the expansion of LSSAF. Radial and circumferential cracks are formed due to the release of stress. 3) Evolution of air plasma follows the conventional evolution process of laser-induced plasma, i. e. , internal pressure, temperature and density decrease quickly with time delay. The simulated transient highest pressure is about 600 MPa. Simulation also predicts the formation of the internal shockwave. Our work will be helpful in understanding the laser damage mechanism of the fused silica optical window.

Laser-Induced Damage Growth on Larger-Aperture Fused Silica Optical Components at 351 Nm

Laser-induced Damage Growth of Fused Silica at 351 Nm on a Large-Aperture High-Power Laser Facility

Laser-induced damage growth of large-aperture fused silica optics under high-fluence 351 nm laser irradiation

Laser-damage Growth Characteristics of Fused Silica under 1064- and 532-Nm Laser Irradiation

Damage Growth Characteristics of Different Initial Damage Sites of Fused Silica under 355 Nm Small Laser Beam Irradiation

Damage Behaviors of Silica Microparticles on Fused Silica Optics under 355 Nm High Fluence Laser

Damage Growth Characteristics on the Exit Surface of Fused Silica by the Low-Temporal Coherence Light Irradiation.

Laser-Induced Damage Initiation and Growth of Optical Materials

Growth of Laser Initial Damage in Conditioned Fused Silica at 355 Nm

Morphological and Damage Growth Characteristics of Shell-Type Damage of Fused Silica Optics Induced by Ultraviolet Laser Pulses.

Behavior of 355 nm laser-induced damage growth in fused silica

Characterization of laser damage performance of fused silica using photothermal absorption technique

Morphology and Growth Properties of Nano- and Submicrometer-Scale Initial Damage Sites under 355 Nm Wavelength Pulsed Laser Irradiation.

Characterization of 355 Nm Laser-Induced Damage of Mitigated Damage Sites in Fused Silica

Experimental and Computational Study of Damage Pocess Induced by 1064 Nm Nanosecond Laser Pulse on the Exit Surface of Fused Silica

Effect of laser ablation on the conductivity and laser-induced damage threshold of fused silica components

Time-resolved Dynamics of 355-Nm Laser-Irradiated Surface Damage on Fused Silica

Study of growth of laser initiated damage in fused silica at 3ω

Atomic Simulation of Surface Damage of Fused Silica under Laser Irradiation

Micron-size bubble defects in fused silica and its laser induced damage near 355 nm

Analysis Method of Point Defects Evolution in Fused Silica under Multi-Pulse Nanosecond Laser Irradiation