Abstract:In this study, the in-situ ZrB 2 /Al-Si5Cu3 aluminum alloy composites were fabricated through the salt-melt reaction route with different weight fractions of ZrB 2 reinforcements, i.e., 2.5%, 5%, and 7.5%. The composites were tested for their density, hardness, tensile strength, flexural strength, impact strength, and wear properties. The influence of reinforcement on the properties was studied concerning the wt.% of reinforcement. The increase in density of composites compared to the matrix material confirms the formation of the in-situ reinforcement phase. The microstructure showed a desirable distribution of reinforced particles over the matrix at all weight fractions of the reinforcements in the composites. The ZrB 2 particles formed in the matrix have particle sizes in the range from 255 nm to 955 nm and the grain size has been reduced from 242 microns to 110 microns as the result of particle-induced solidification. The hardness of the composites containing ZrB 2 reinforcements of 2.5, 5, and 7.5 wt.% showed improvement by 8%, 17.5%, and 34% respectively compared to the parent alloy. There is an improvement in the tensile strength and elongation for the wt.% of ZrB 2 up to 5 wt.%, from 115 MPa to 183 MPa, after which, there was a drop in the tensile strength. The detailed analysis of tensile fractography shows that the agglomerated ZrB 2 reinforced particles at higher weight fractions lead to a decrease in strength. The results of flexural strength also affirm the strength of 5 wt.% ZrB 2 /Al-Si5Cu3 increased from the matrix material's flexural strength of 337 MPa to 672 MPa. The wear study shows that the composite with 7.5 wt.% ZrB 2 possesses a higher wear resistance. However, the impact strength did not show any differences in the weight % of reinforcement.

Fabrication and properties of in situ (Al3Zr + Al2O3)p/A356 composites cast by permanent mould and squeeze casting

In situ (Al3Zrp+Al2O3np)/2024Al metal matrix composite with controlled reinforcement architecture fabricated by reaction hot pressing

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Fabrication of Nanocrystalline Zro2 Particle Reinforced Aluminum Alloy Composite by Squeeze Casting Route

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

High-Resolution Electron Microscope Observation of Interface Microstructure of A Cast Al-Mg-Si-Bi-Pb(6262)/Al2o3p Composite

In situ (Al3Zr + Al2O3np)/2024Al metal matrix composite with novel reinforcement distributions fabricated by reaction hot pressing

Preparation and mechanical and tribological properties of A1(3)Zr+6082Al composites fabricated by magnetic stirring in situ

High Strength Al(2)O(3)P/6061 Al Composites: Effect Of Particles, Subgrains And Precipitates

Microstructures and mechanical properties of the in-situ formed nanocomposites of (ZrB2 + Al2O3) and AA7055 alloy

Preparation and Mechanical and Tribological Properties of A13Zr+6082Al Composites Fabricated by Magnetic Stirring in Situ

High strength Al<SUB>2</SUB>O<SUB>3p</SUB>/6061 Al composites: effect of particles, subgrains and precipitates

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

Microstructure of ZrB<sub>2</sub>/6063Al <i>In Situ</i> Composite Processed by Forge

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Mechanical and Wear Behavior of Al-Si5Cu3/ZrB2 In-Situ Reinforced Metal Matrix Composite

Microstructural, mechanical, and wear properties of ultrasonic assisted stir casted A356 Alloy/AlN composite

Fabrication and characterization of stir casting AA6061-31% B4C composite

Microstructural, hardness, and wear properties of Mg 2 Si-reinforced Al matrix in-situ composites produced by low superheat casting

Fabrication and strengthening mechanism of dual-phased and bimodal-sized (Si3N4p + TiB2p)/6061Al hybrid composite

Microstructure and mechanical behavior of Mg ZK60/Al 1100 composite plates fabricated by co-extrusion