Abstract:For axial turbines, tip leakage vortex and passage vortex flow are responsible for a large part of the aerodynamic loss. To pursue higher turbine efficiency, many methods are undertaken to eliminate the tip leakage loss. In this work, by experimental and numerical methods, novel wave-shaped tip-shroud contours on the unshrouded turbine cascade were proposed. In a low-speed large-scale linear turbine cascade facility, a traditional flat tip was first conducted to comprehensively validate the numerical tool, especially the inlet conditions and the total pressure loss due to the tip leakage loss. The numerical settings were kept the same as the experimental facility. It achieved a satisfactory agreement between the CFD and experiments. It was found that in a flat tip case, a large, integral tip leakage vortex structure was identified and responded to the aerodynamic loss within the tip leakage core. Then a series of novel wave-shaped tip-shroud contours were considered in the current turbine cascade. The overtip flow exited the suction side tip gap, and the peak mass flow rate was concentrated around the troughs of the wave tip. Several small-sized, but stronger-vorticity-magnitude vortex structures were identified. By breaking down a large, integral vortex structure into several smaller-scale vortices, the vortex evolution was beneficial for the turbine efficiency. Although a slight enhancement of passage vortex was identified, the overall loss reduction of 3.0% was achieved by reducing the tip leakage loss, which dominated the loss contribution. According to the real working condition, axial displacement for the blade was considered. Within the current scope, the maximum reduction of tip leakage loss coefficient was reduced by 14.6% compared to the flat tip case. It was mainly contributed by the smaller contraction coefficient within the tip gap, which reduced the overtip leakage mass flow. Meanwhile, the vena contracta within the tip gap was altered, as well as static pressure distribution on the tip surface. As a result, the minimum static pressure was re-distributed at the throat of the tip gap. It was proven that this novel wave-shaped tip-shroud contour was an efficient way to improve the aerodynamic performance at a larger tip gap.(c) 2022 Elsevier Ltd. All rights reserved.

Design of High Efficiency Turbine with Large Tip Clearance for Rocket Engine

Optimization Design of Aspect Ratio and Solidity of a Heavy-Duty Gas Turbine Transonic Compressor Rotor

A Novel Design Towards Reducing Leakage Loss for Variable Geometry Turbines

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Influence of Blade Lean Together with Blade Clocking on the Overall Aerodynamic Performance of a Multi-Stage Turbine

Unsteady Aerodynamics Of A Flat Tip And A Winglet Tip In A High-Pressure Turbine

Novel Wave-Shaped Tip-Shroud Contours Towards Reducing Turbine Leakage Loss

A Cfd Approach to Fluid Dynamic Optimum Design of Steam Turbine Stages with Stator and Rotor Blades

Fluid Dynamic Efficiency Optimization of Steam Turbine Stages Considering Leakage Influences and Inter-stage Reciprocal Interferences

AERODYNAMIC ANALYSIS OF A 7-STAGE AXIAL COMPRESSOR WITH VARIOUS TIP CLEARANCES IN ROTOR

Design and Analysis of a Turboshaft Engine Turbine

Optimization of Rotor Tip Cavity Shapes for Mitigating Aerodynamic Tip Leakage Losses

Aerodynamic design of a high-efficiency two-stage axial turbine, using streamline curvature method and performance optimisation by clocking of stator blades

Investigation on the Interaction of Tip Leakage Flow/ Shock Wave/ Boundary Layer in a Transonic Compressor Stage

OPTIMIZATION DESIGN FOR THE TURBINE TRANSITION SECTION OF AN AEROENGINE

CFD simulation and aerodynamic optimization of two-stage axial high-pressure turbine blades

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

Unsteady Flow Loss Mechanism and Aerodynamic Improvement of Two-Stage Turbine under Pulsating Conditions

DESIGN, MULTI-POINT OPTIMIZATION AND ANALYSIS OF DIFFUSIVE STATOR VANES TO ENABLE TURBINE INTEGRATION INTO ROTATING DETONATION ENGINES

Design Of Counter-Rotating Turbine To Improve The Off-Design Performance Of Turbo-Compounding Systems

Optimization of the Blade Trailing Edge Geometric Parameters for A Small Scale Orc Turbine