Abstract:In the recent decades, there has been an increasing interest in preparing novel polymeric blending materials with combined and additional characteristics of each component. Having a relatively high modulus, toughness and strength, low creep, and good temperature resistance, nylons have been widely applied in the automotive industry, machinery, electronic equipment, and military applications [1]. It is well-known that blends consisting of nylon and elastomer possess excellent toughness; however, due to its highly polar amide end-groups, nylon is incompatible with elastomer. In general, it is believed that functionalization of the elastomer is a preferred approach to enhance the interfacial properties between these polymers. Research concerning nylon/functionalized elastomer blends has mostly focused on the aspects of mechanical and thermal properties. To our knowledge, only a few reports have dealt with dynamic rheological behavior of their melts [2–4]. The rheological measurements not only give much useful information for material moulding and processing, but also is an important way to characterize the structure and properties of polymer materials [5, 6]. The aim of this article is to study the influence of the graft reaction between nylon1212 and SEBS-gMA on dynamic rheological behavior and morphology of their blends. Nylon1212 (melt-flow index = 22.43 g/min) used here was obtained from Shandong Dongchen Engineering Plastic Co., Ltd., China. The elastomer, a triblock copolymer styrene-b-(ethylene-co-butylene)-b-styrene (SEBS 4033) was supplied by the Yuyao Huiju Polymer Co., Ltd. China. The maleated triblock copolymer styrene-b-(ethylene-co-butylenes)-b-styrene (SEBS-gMA) was supplied by Yuyao Yongcheng Engineering plastics Co., Ltd., China. The grafting ratio of maleic anhydride is 1.84 wt%. Both SEBS and SEBSg-MA consist of 30 wt% polystyrene end-blocks. The nylon1212/SEBS blends and nylon1212/SEBS-g-MA blends including 1 wt% antioxidant (1010) were prepared in a corotating twin-screw extruder (PRISM TES 16TC, UK) at 210 ◦C. All the samples were compression-moulded into disks of 25 mm in diameter and 1.2 mm in thickness at 180 ◦C, 50 MPa. Melt rheological tests were conducted in an ARES Rheometer

Preparation of isocyanate functionalized styrene-ethylene-butadiene-styrene copolymer and its blending with polyamide 6

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Study on ester-amide exchange reaction between PBS and PA6IcoT

The Effect of Functionalized SEBS on the Properties of PP/SEBS Blends

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Synthesis of graft copolymer of polystyrene and polyamide 6 by activated anionic polymerization

Synergistic Effect of Sbs and Trimethylopropane Trimethacrylate (tmptma) on Dynamically Vulcanized Sebs/Pp Blends

Surface Functionalization Of Polypropylene-Bearing Isocyanate Groups In Solid State And Their Cyclotrimerization With Diisocyanates

Reactive Compatibilization and Elastomer Toughening of Poly(2,6-dimethyl-1,4-phenylene Oxide)/polyamide 6 Blends

FUNCTIONALIZATION OF POLYPROPYLENE AND COMPATIBILIZATION OF POLYPROPYLENE/NYLON 6 BLENDS WITH Α-Methyl STYRENE/STYRENE/MALEIC ANHYDRIDE TERNARY COPOLYMER

Synthesis, Copolymer Composition, and Rheological Behavior of Functionalized Polystyrene with Isocyanate and Amine Side Groups

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Ternary Polymer Composites: PA6,6/maleated SEBS/glass Beads

Preparation and Properties of PA10T/PPO Blends Compatibilized with SEBS-g-MAH

The dynamic rheological behavior and morphology of nylon/elastomer blends

Functionalization of Polypropylene and Compatibilization of Polypropylene/Nylon 6 Blends with Copolymers Containing Alpha-Methyl Styrene Units

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

Comprehensive Investigation on the Synthesis of Polyamide 6 and Polyurethane Elastomer Blends Via in Situ Polymerization

Solvothermal Process for Synthesis of Macromolecules Compatibilizer of Polypropylene Containing Isocyanate Ester Groups

Maleic Anhydride-Grafted Isotactic Polybutene-1 and Modified Polyamide 6