Abstract:The production of alkali-activated materials (AAMs) is known for its environmentally friendly processing method, where several amorphous-rich aluminosilicate material sources combine with an alkali media solution to form solid, ceramic-like materials. In terms of the Si:Al, Na(K):Al, and Na(K):H 2 O ratios, the theory of AAM formation is quite well developed, but some open questions in the technology process remain, especially with regards to the means of curing, where the generation of defects can be persistent. Knowing that deformation is extremely high in the early ages, this study investigates the effects of temperature and moisture on shrinkage behavior within the first 72 h of AA pastes made from ladle (LS) and electric arc furnace (EAF) slag and activated by sodium silicate (Na 2 SiO 3 ). The method to determine the deformation of alkali-activated slag-based materials, in terms of both autogenous and drying shrinkage, was based on the modified ASTM C1698-19 standard for the measurement of autogenous shrinkage in cement pastes. Autogenous deformation and strain were measured in four samples, using the standard procedure at room temperature, 40 and 60°C. Furthermore, using an adjusted method, nine samples were characterized for strain and partial surface pressure, while drying at room temperature, 40, or 60°C at a relative humidity of 30 or 90%. The results show that the highest rate of autogenous shrinkage occurred at a temperature of 60°C, followed by drying shrinkage at 60°C and 30% relative humidity, owing to the fact that the rate of evaporation was highest at this moisture content. The study aimed to provide guidance regarding selection of the optimal curing set in order to minimize deformations in slag-based alkali-activated materials. In the present case, curing at a temperature of around 40°C under lower moisture conditions for the first 24 h provided optimal mechanical properties for the slags investigated. The methodology might also be of use for other aluminosilicate sources such as metakaolin, fly ash, and mineral wool–based alkali-activated materials.

Effect of Heat-Treatment on Dielectric Performances and Microstructure of Alkali Active Slag Cement Materials

EFFECT OF WATER ON DIELECTRIC PERFORMANCES OF ALKALI ACTIVE SLAG CEMENT MATERIALS(Ⅰ)

Behaviour of alkali-activated fly ash-slag paste at elevated temperatures: An experimental study

Temperature Effect of Hydration and Microstructure of Tricalcium Silicate–Slag Powder Hydrated Composites: An Experimental and Molecular Dynamics Investigation

Research on rheology performance and sealing effect of alkali-activated GGBS paste used for tunnel leakage plugging

Effect of Alkali Content on the High-Temperature Behavior of Alkali-Activated Slag Paste Containing MSWI Bottom Ash

Effect of Waste Ceramic Powder on the Properties of Alkali–Activated Slag and Fly Ash Pastes Exposed to High Temperature

Impact of heat curing regime on the compressive strength and drying shrinkage of alkali-activated slag mortar

Hydration characteristics and microstructure development of sodium hydroxide slag pastes exposed under different curing environments

Influence of Different Alkali Sulfates on the Shrinkage, Hydration, Pore Structure, Fractal Dimension and Microstructure of Low-Heat Portland Cement, Medium-Heat Portland Cement and Ordinary Portland Cement

Investigation of shrinkage mechanism of alkali-activated slag

Deformation of Alkali-Activated Materials at an Early Age Under Different Curing Conditions

Experimental Investigations on Alkali-Activated Slag Cementitious Material

Effect of Different Curing Conditions on the Strength Development of Alkali-Slag-Metakaolin Composite Cementitious Material

Effects of alkali dosage and silicate modulus on autogenous shrinkage of alkali-activated slag cement paste

Recent progress in understanding setting and hardening of alkali-activated slag (AAS) materials

An investigation on frost resistance and pore structure of alkali-activated slag concrete

Effect of curing conditions on the alkali-activated blends: Microstructure, performance and economic assessment

Influence of slag on microstructure of complex binder pastes

Effect of internal sulfate attack on the properties of sulfate-resisting cement and alkali-activated slag

Enhancing Freeze-Thaw Resistance of Alkali-Activated Slag by Metakaolin