Abstract:In the present work, two processing routes (A and B) with 3 CEE-AEC passes are performed on Mg–13Gd–4Y–2Zn–0.4Zr alloys, and the resultant microstructure evolution, texture analysis and mechanical properties are investigated systematically. The core difference between the two processing routes is the orientation between the expansion and extrusion steps, i.e., they are parallel to each other for on route A and perpendicular to each other for route B. The results show that a remarkable grain refinement is achieved via both processing routes due to dynamic recrystallization (DRX). Fine equiaxed grains are observed in the samples processed with route B with a final size of 3.6 ± 0.4 µm compared to the grain size of 4.5 ± 0.5 µm with route A. With an increasing number of CEE-AEC passes, the overall texture intensity decreases, and the basal texture gradually changes to the mixed texture components. The shear deformation introduced by the asymmetrical extrusion cavity promotes a broad angular distribution of the basal planes on routes A and B, leading to an obvious increase in the Schmid factor for the activation of the basal 〈a〉 slip system. The tensile test at ambient temperature reveals that the comprehensive mechanical properties are improved, and the conventional mechanical anisotropy of as-received alloys is alleviated by successive CEE-AEC processing, which is mainly derived from the competitive balance relation between the grain refinement and texture modification.

Comparison Of Microstructure And Texture Development Of Ecaped Pure Mg With A Mg-Si Alloy

Microstructure and Mechanical Property of the Ecaped Mg2si/Mg Composite

Microstructure and tensile property of the ECAPed pure magnesium

Microstructure Evolution and Mechanical Behavior of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP at High Temperature

Microstructural evolution and mechanical response of duplex Mg-Li alloy containing particles during ECAP processing

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Influence of ECAP Routes on Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy

Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy Processed by Equal Channel Angular Pressing

Effect of ECAE Conditions on the Microstructure, Texture and Mechanical Properties of an Extruded Mg–Zn–Y–Zr Alloy

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Anisotropy investigation of an ECAP-processed Mg-Al-Ca-Mn alloy with synergistically enhanced mechanical properties and corrosion resistance

Microstructural Evolution and Mechanical Properties of Mg95.5Y3Zn1.5 Alloy Processed by Extrusion and ECAP

Microstructure Evolution of AZ Series Magnesium Alloys During Cyclic Extrusion Compression

Microstructure Evolution in Magnesium Alloy AZ31 During Cyclic Extrusion Compression

Improved Mechanical Property and Internal Friction of Pure Mg Processed by ECAP

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Microstructure Evolution of Processed Mg-Al-Zn Alloy by Equal Channel Angular Extrusion in Semi-Solid Isothermal Treatment

Microstructure and Mechanical Property of Pure Magnesium Processed by Cyclic Extrusion Compression

Microstructure and Texture Characteristics of Zk60 Mg Alloy Processed by Cyclic Extrusion and Compression

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Microstructure evolution, texture and mechanical properties of a Mg–Gd–Y–Zn–Zr alloy fabricated by cyclic expansion extrusion with an asymmetrical extrusion cavity: The influence of passes and processing route