Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Suspension Viscosity-temperature Characteristic on Tribological Properties of Abrasive Flow Machining Process

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Temperature As Sensitive Monitor for Efficiency of Work in Abrasive Flow Machining

Impact of fluid abrasive viscosity on machining performance

Temperature Dependence and Effect on Surface Roughness in Abrasive Flow Machining

On surface texture evolution in abrasive flow machining

Study on Rheological Behaviors of Media and Material Removal Mechanism for Abrasive Flow Machining (AFM) Micro Structures and Corresponding Simulations

Material Removal Rate Model of High Viscoelastic Fluid Abrasive Finishing

Experimental and Modelling Study of Friction Evolution and Lubricant Breakdown Behaviour under Varying Contact Conditions in Warm Aluminium Forming Processes

Research on the underlying mechanism behind abrasive flow machining on micro-slit structures and simulation of viscoelastic media

Study on the wear performance of 304 stainless steel aerospace joint bearings

Modelling of Tribological Behavior and Wear for Micro-Textured Surfaces of Ti2AlNb Intermetallic Compounds Machined with Multi-Dimensional Ultrasonic Vibration Assistance

Cryogenic tribological behavior of coarse, ultrafine grained and heterogeneous Fe-18Cr-8Ni austenitic stainless steel

Application of Taguchi Method Design to Investigate Tribological Performance of Laser-Surface-Textured 316L Austenitic Stainless Steel

Numerical Analysis for Influence of Temperature on Polishing Quality of Dispensing Deads by Multi-physics Coupled Field Abrasive Flow

Effect of Vibration Frequency on Tribological Characteristics of Vibration-Assisted Micro-Nano Machining

Removal Mechanism of Hydrodynamic Suspension Ultra-smooth Machining for Hard-brittle Materials

Process-surface morphology-tribological property relationships for H62 brass employing various manufacturing approaches

A Mixed Lubrication Model for Studying Tribological Behaviors of Surface Texturing

Experimental Investigations into Abrasive Flow Machining of Helical Gear

Additional Tribological Effect of Laser Surface Texturing and Diamond-Like Carbon Coating for Medium Carbon Steel at Near Room Temperature