Abstract:The Atacama Large Millimeter and Submillimeter Array (ALMA) band 10 cartrid es are being designed based on use of waveguide components such as couplers, because of their mechanical ruggedness and reliability. Although recent machining technology makes it possible to fabricate such small waveguide components with sizes of down to several tens of microns, it is important to characterize their electrical performance experimentally at room and cryogenic temperatures. For the room temperature measurements, we have developed a vector network analyzer, which consists of a W-band Gunn oscillator followed by a nonupler as a transmitter and a subharmonic Schottky diode mixer pumped by another W-band Gunn oscillator as a receiver. Both Gunn oscillators are phase-locked to a sin g le microwave reference, but on different sidebands. The device under test (DUT) is put between the transmitter and the receiver and the insertion loss and phase difference is measured. For the cryogenic temperature measurements, we used SIS mixers consisted of a corrugated horn and a mixer block. These are connected by a common waveguide flange. The DUT is inserted between them. By measuring the mixer gains or noise temperatures with and without the DUT, the insertion loss is simply estimated from the chan e of the gains or noise temperatures due to the input loss. Fi g ure 1 shows a photograph of a 10-dB directional coupler with WR-1.2 (0.305 0.152 mm) gold-plated waveguide made by machining. The total len th of the wavcguides is 30 mm. Figure 2 shows the measured insertion losses at room temperature. This result is reasonable if we assume an electrical conductivity of the gold at room temperature, which suggests that the part of the 10-dB coupler with two slits works well as expected. however, the insertion loss at cryogenic temperature showed a lare loss of about 1.8 dB/30 mm. To confirm this unexpected waveguide loss, we measured the loss in a 25-mm-length straight waveguide as well. The result showed the waveguide losses of about 1.3 d13125 mm, which is similar to the result of the 10-dB coupler. This implies that the length of the waveguide components should be designed as short as possible to reduce the waveguide loss in more than this frequency band.

Development Of The 787-950 Ghz Alma Band 10 Cartridge

Development of ALMA Band 8 (385-500 GHz) Cartridge

Design and Development of SIS Mixers for ALMA Band 10

A Sensitive ALMA Band 10 SIS Receiver Engineering Model

Performance of the ALMA Band 10 SIS Receiver Prototype Model

Superconducting Receiver Technologies Supporting ALMA and Future Prospects

A 385-500 GHz Low Noise Superconductor-Insulator- Superconductor Mixer for ALMA Band 8.

Performance and Uniformity of Mass-Produced SIS Mixers for ALMA Band 8 Receiver Cartridges

Development of Superconducting Devices Supporting Radio Astronomy.

Wideband 67-116 GHz cryogenic receiver development for ALMA Band 2

Development of the ALMA-North America Sideband-Separating SIS Mixers

Wideband Technology Development to Increase the RF and Instantaneous Bandwidth of ALMA Receivers

M1B Evaluation of ALMA Band 8 S/N01 Cartridge

A 385-500 GHz 2SB SIS mixer based on a waveguide split-block coupler

TH 2-6 1 A 385-500 GHz 2 SI 3 SIS Mixer Based on a Waveguide Split-Block Coupler

A 60–90 GHz Mixer-First Receiver with Adaptive Temperature-Compensation Technique

A 385–500 GHz Sideband-Separating (2SB) SIS Mixer Based on a Waveguide Split-Block Coupler

Development of a 0.85 THz Nb-AlN-NbN Superconductor-Insulator-superconductor Mixer

Characterization of Waveguide Components for the ALMA Band 10

A Compact 500ghz SIS Receiver Developed for Space Observations

Development of a Submillimeter Double-Ridged Waveguide Ortho-Mode Transducer (OMT) for the 385–500 GHz Band