Abstract:The Atacama Large Millimeter and Submillimeter Array (ALMA) band 10 cartrid es are being designed based on use of waveguide components such as couplers, because of their mechanical ruggedness and reliability. Although recent machining technology makes it possible to fabricate such small waveguide components with sizes of down to several tens of microns, it is important to characterize their electrical performance experimentally at room and cryogenic temperatures. For the room temperature measurements, we have developed a vector network analyzer, which consists of a W-band Gunn oscillator followed by a nonupler as a transmitter and a subharmonic Schottky diode mixer pumped by another W-band Gunn oscillator as a receiver. Both Gunn oscillators are phase-locked to a sin g le microwave reference, but on different sidebands. The device under test (DUT) is put between the transmitter and the receiver and the insertion loss and phase difference is measured. For the cryogenic temperature measurements, we used SIS mixers consisted of a corrugated horn and a mixer block. These are connected by a common waveguide flange. The DUT is inserted between them. By measuring the mixer gains or noise temperatures with and without the DUT, the insertion loss is simply estimated from the chan e of the gains or noise temperatures due to the input loss. Fi g ure 1 shows a photograph of a 10-dB directional coupler with WR-1.2 (0.305 0.152 mm) gold-plated waveguide made by machining. The total len th of the wavcguides is 30 mm. Figure 2 shows the measured insertion losses at room temperature. This result is reasonable if we assume an electrical conductivity of the gold at room temperature, which suggests that the part of the 10-dB coupler with two slits works well as expected. however, the insertion loss at cryogenic temperature showed a lare loss of about 1.8 dB/30 mm. To confirm this unexpected waveguide loss, we measured the loss in a 25-mm-length straight waveguide as well. The result showed the waveguide losses of about 1.3 d13125 mm, which is similar to the result of the 10-dB coupler. This implies that the length of the waveguide components should be designed as short as possible to reduce the waveguide loss in more than this frequency band.

Development of a Submillimeter Double-Ridged Waveguide Ortho-Mode Transducer (OMT) for the 385–500 GHz Band

Development of a 385-500 GHz Orthomode Transducer (OMT)

Broad-Band Orthomode Transducers

Double-Ridged Waveguide Orthomode Transducer for terahertz wireless transmission link

170–260-Ghz Ultrawideband and High Isolation Orthomode Transducer Based on Symmetric Reverse Coupling Structure

Development of ALMA Band 8 (385-500 GHz) Cartridge

A Design of Terahertz Wave Orthomode Transducer (OMT)

A high-performance compact WR-4 orthomode transducer for wideband communications

Design of a Compact Waveguide Orthomode Transducer at Terahertz Frequency

Optimization of Asymmetric Orthomode Transducer at Terahertz Frequency

Very Compact Waveguide Orthomode Transducer in the K-Band for Broadband Communication Satellite Array Antennas

Performance of the ALMA Band 10 SIS Receiver Prototype Model

Development of Wideband Orthomode Transducers for FAST Cryogenic Receiver System

A Sensitive ALMA Band 10 SIS Receiver Engineering Model

Near-field Beam Pattern Measurement of Qualification Model of ALMA Band 8 (385–500 GHz) Cartridge Receiver

Characterization of Waveguide Components for the ALMA Band 10

Wideband 67-116 GHz cryogenic receiver development for ALMA Band 2

M1B Evaluation of ALMA Band 8 S/N01 Cartridge

Compact W-Band Septum Orthomode Transducer Based on Gap Waveguide

Wideband Turnstile Junction Coaxial Waveguide Orthomode Transducer

A 385–500 GHz Sideband-Separating (2SB) SIS Mixer Based on a Waveguide Split-Block Coupler