Abstract:The present study is an experimental work carried for surface alloying/modification of D2 alloy steel using WC/Co powder metallurgy (P/M) electrode made of nano, micron and mixture of nano and micron sized particles. Both, machine tool and electrode parameters were selected for study and experiments were planned as per Taguchi's L18 mixed orthogonal array. Optimal combination of parameters was obtained using Taguchi's method and analysis of variance (ANOVA) was performed to evaluate influence of parameters on surface roughness (SR) and micro-hardness (MH). The parameters Peak current (IP), pulse on time (TON) and particle size (PS) were found to be most influential on both SR and MH. In EDM, surface modification is performed by deliberate transfer of tool elements onto the work surface. In the present investigation, EDS analysis reveals the migration of tungsten (W) and cobalt (Co) electrode particles, deposition of carbon particles and diffusion of oxygen particles onto the work surface. High reactive surface area of nano particles made greater surface alloying than other tool electrodes and has shown its influence positively on both SR and MH. Low thermal conductivity of nano particle electrodes (NP) makes improved surface alloying than other tool electrodes. Because of the particle size is reduced to nano level its dimension is smaller than the spark gap dimension hence, reduced arcing and improved process stability was obtained, which eventually improved the surface roughness of the component. At optimum MH, higher values of TON and IP gives the sufficient time and temperature for formation of following carbides and oxides viz., Fe3C, Cr23C6 , Cr2Fe14C, Fe2W2C, W3O and Cr3O were responsible for increased hardness of the work surface. The range of roughness values obtained in the present investigation is 1.65-5.82 μm. The highest hardness of 981 HV was obtained without much sacrificing the surface finish.

Surface Properties of Powder Mixed EDM of TaW Alloy Material

Surface Properties of 3000°C High Melting Point Material by Powder Mixed EDM

Study On Micro-Edm Of A 3 000 Degrees C High Melting Point Material

Multiple Needle Cathodes Plasma Surface Alloying of Ti6Al4V with W-Mo-C-N

Performance comparison of powder mixed EDM and traditional EDM on TZM-molybdenum super alloy using response surface methodology

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Preparation, Microstructure, and Microhardness of Selective Laser-Melted W–3Ta Sample

Study on the Machining of High Melting Point Material by Using Powder Mixed EDM

Surface alloying of D2 steel using EDM with WC/Co P/M electrodes made of Nano and Micron sized particles

On the WEDM of WNbMoTaZr x (x = 0.5, 1) Refractory High Entropy Alloys

Microstructural Evolution and Mechanical Properties of Spark Plasma Sintering of Tantalum-Tungsten Alloy

Microstructure and Properties of Ta-W Alloys Fabricated by Spark Plasma Sintering Technology

Surface modification of WC-Co alloy using Al and Si powder through WEDM: A thermal erosion process

Studies on the Surface of High-Performance Alloys Machined by Micro-Edm

Influence of electrical parameters in electro discharge machining of tungsten heavy alloys on surface texture properties

Machinability investigation and surface modification of nano-TiB2 and AlN grafted MWCNT hybridized Al 7075 matrix ternary composite through powder-mixed EDM

Study on Powder Mixed EDM of an Aluminium Matrix Composite

Micro Electrical Discharge Machining of Ultrafine Particle Type Tungsten Carbide Using Dielectrics Mixed with Various Powders

Microstructure, Wear Behaviour and Laser Ablation Behaviour of Double Glow Plasma Alloyed Ta-W Coating

Investigation on Surface Roughness and MRR in WEDM of Titanium Grade 7 (Ti-0.15Pd) Alloy using Statistical Techniques

Development of Tungsten As Plasma-Facing Materials by Doping Tantalum Carbide Nanoparticles